Abstract:It is common knowledge that one of the main issues of hypersonic flight is the thermal management of the overall vehicle and more specifically the cooling of the engine, since even composite materials can't withstand the large heat load found in a Scramjet combustion chamber. The other critical point is that mixing and combustion should be sufficiently fast in order to avoid long combustion chamber caused by supersonic internal flow and short residence time. This dual requirement leads to the idea of using inboard fuel as coolant, in order to limit the weight of the cooling system and to benefit from some fuel endothermic capability, i.e. the capability of heavy hydrocarbon fuels to decompose into lighter species, mainly methane, ethane, hydrogen and alkenes from C2 to C10, providing welcomed additional heat sink. Analytical (such as NANCY code) and multidimensional tools (such as CFD-ACE), extensively used for design and analysis of metallic and composite cooled structures are also very efficient to address hydraulic and thermal phenomenon, but, up to now, these approaches did not compute the chemical decomposition of the fuel, except by the way of assumed thermo -dynamical properties. Due to the large number of components found in a traditional jet fuel, the characterization of the thermal decomposition of such products is not a simple issue. In order to obtain a good understanding of the various phenomenon inside a cooled panel of a Scramjet, we selected n-dodecane as a representative surrogate for envisioned endothermic fuel. The thermal decomposition model for n-dodecane was developed by the DCPR and validated thanks to available experimental data. This model, written in a CHEMKIN II format, has been proved able to describe the behavior of n-dodecane between 600 1100 K and 110 bar and could certainly be extrapolated in a wider temperature and pressure range, without taking specifically into account the supercritical phase. This paper will present some numerical results obtained for a cooled composite panel under different heat loads, from a physical point of view (temperature of the panel) and a chemical point of view (composition of the decomposed fuel). INTRODUCTION In a large part of the flight regime, the air-breathing mode appears to be a good solution for future Reusable Space Launchers (RSL). Dual-mode ramjets have been studied to propel such TSTO (Two-Stage To Orbit) or Single -Stage To Orbit (SSTO) vehicles. For example, in the scope of the French PREPHA program, the study of a generic SSTO vehicle led the conclusion that the best type of air-breathing engine could be the Dual-Mode Ramjet (DMR, with subsonic then s upersonic combustion). Airbreathing launchers could typically use hydrogen-fuelled DMR. Less energetic fuels like hydrocarbons could also be used at a Mach number of flight lower than 8, to take advantage of their higher density. In this case, the engine must be able to manage two different fuels. DMR or scramjets designed for hypersonic military applications are typically associated with liquid hydrocarbons and with a maximum flight Mach number of 8 (missiles). Given the very high heat load inside the combustion chamber, active cooling seems to be the only way for a proper thermal management of the engine (Figure 1).

Thermodynamic analysis on the performance of hydrocarbon fueled scramjet with inlet active cooling

SHOCK INDUCED SEPARATING FLOWS IN SCRAMJET INTAKES

Feasibility and performance evaluation of film cooling using incoming air in a gel-fueled scramjet

Nonequilibrium Heating/Cooling Effects in a Mach Number 10 Hydrogen-Fueled Scramjet

Progress of Coupled Heat Transfer Mechanisms of Regenerative Cooling System in a Scramjet

Numerical Investigation of the Thermal-Mechanical Behaviors in the Regenerative Cooling Channel Considering Thermal Pyrolysis

Numerical investigation on regeneration-transpiration combined cooling of cavity structure in scramjet engine

On compression level of hypersonic airflow in high-mach scramjet

CONTRIBUTION TO SCRAMJET ACTIVE COOLING ANALYSIS USING N-DODECANE DECOMPOSITION MODEL AS A GENERIC ENDOTHERMIC FUEL

Study of Heat Transfer of Composite Lattice Structure for Active Cooling Used in the Scramjet Combustor

Flow maldistribution and heat transfer non-uniformity with an inlet baffle structure in regenerative cooling channels

Large eddy simulation of boundary layer combustion of hydrogen and hydrocarbon fuel films in a modeled scramjet combustor

A review of regenerative cooling technologies for scramjets

Combustion dynamics of high Mach number scramjet under different inflow thermal nonequilibrium conditions

Numerical Investigation of Convective Heat Transfer of Supercritical Hydrocarbon Fuel in a Tube Filled With Porous Media

Optimization of scramjet inlet based on temperature and Mach number of supersonic combustion

Thermo-chemical nonequilibrium effects on combustion characteristics of a transverse jet in the scramjet

Influences of interconnection structure on the flow and heat transfer behaviors of the hydrocarbon fuel in parallel SCRamjet regenerative cooling channels

Numerical investigation of thermochemical non-equilibrium effects in Mach 10 scramjet nozzle

Insight into jet-regeneration composite cooling technology employed in scramjet: Significance of relative positions of two jet holes

Numerical Study on Flow and Heat Transfer of Supercritical Hydrocarbon Fuel in Curved Cooling Channel