Abstract:This paper attempts to present a brief review of recent progress obtained by the author's group in the research area of ion beam metallurgy, namely (i) formation of metal-nitride by nitrogen implantation; (ii) metallic glass formation by ion mixing; and (iii) icosahedral phase formation by ion mixing. Silver- and copper-trinitrides have been formed, for the first time, by RT 80 keV nitrogen ion implantation for doses up to 2×10 18 N cm −2 . These indicated that deposition of large amounts of energy during implantation could provide the reaction energy of noble-metal-nitride with rather positive heat of formation, and that local nitrogen concentration in the implanted films could be considerably greater than that limited by the sputtering yield involved. Besides, our observation of the reverse sequence of phase transition TiTiNTi 2 N with increasing nitrogen dose suggested that growth kinetics (or structural compatibility between newly formed phase and the matrix) might be a key factor in determining the nitride formation in some systems. Two parameters were found of importance in influencing the glass forming ability (GFA) of binary metal systems. One is MPAR (maximum possible amorphization range), which equals 100% minus the maximum solid solubilities observed in the equilibrium phase diagram. The other is the heat of formation. A map was constructed by these parameters and some empirical qualifications were found to classify the systems according to GFA into three categories of Hardly (HGF), Possible (PGF) and Readily (RGF) Glass Forming systems. The FeCu system is an immiscible one, in which amorphization induced by ion mixing could only occur within a narrow composition range. The favored composition was figured out experimentally, and an icosahedral phase was also formed by ion mixing without post-annealing at corresponding atomic stoichiometry. Interestingly, a similar phase was also formed in the FeMo system.

Influence of Ionic Species on Phase Formation in Ion Mixing of Carbon Films on Tungsten

Nucleation and growth of amorphous carbon film on tungsten-implanted stainless steel substrates

Tungsten Carbide Nanolayer Formation by Ion Beam Mixing with Argon and Xenon Ions for Applications as Protective Coatings

Insights into the Nucleation, Grain Growth and Phase Transformation Behaviours of Sputtered Metastable Β-W Films

Formation Of Nanocrystalline Tin Film By Ion-Beam-Enhanced Deposition

Formation Of Transition-Metal Carbide Thin-Films By Dual Ion-Beam Deposition At Room-Temperature

Irradiation induced non-equilibrium phase formation and structural transformation in the Fe–Ti–Nb multilayered films

A Dodecagonal Phase Formed in an Immiscible Co-Ag System by Ion Mixing of Multilayers

Structural Phase Transition Induced by Ion Irradiation in the Equilibrium Immiscible Ag–Co System

Phase Evolution Upon Ion Mixing and Solid-State Reaction and Thermodynamic Interpretation in the Ni-Nb System

Phase composition of sputter deposited tungsten thin films

Non-equilibrium Alloy Phase Formation and Transformation Driven by Ion Beam Mixing in the Fe-Hf-Nb Multilayers

Effect of depositing parameters on microstructures and properties of multi arc ion plating ZrTiN films

Evolution Mechanism of Nanocrystalline Tungsten-Carbon and Effects on Tungsten Implanted Amorphous Hydrogenated Carbon

Study Of Alloy Phase Formation Using Ion-Beams

Phase Control and Young's Modulus of Tungsten Thin Film Prepared by Dual Ion Beam Sputtering Deposition

Effects of Tungsten Pre-Implanted Layer on Corrosion and Electrochemical Characteristics of Amorphous Carbon Films on Stainless Steel

Mechanical Properties of Tungsten Doped Amorphous Hydrogenated Carbon Films Prepared by Tungsten Plasma Immersion Ion Implantation

Solid State Phase Transition Induced by Ion Irradiation in the Co-Nb System: Experiments and Thermodynamics

Structural phase transition in the Hf–Ni system studied by ab initio calculation and ion beam mixing

Formation of A Metastable Cubic Phase in an Immiscible Fe-Ag System by Ion Mixing