Abstract:Recent advances in additive manufacturing (AM) have enabled the fabrication of functionally graded porous biomaterials (FGPBs) for application as orthopedic implants and bone substitutes. Here, we present a step-wise topological design of FGPB based on diamond unit cells to mimic the structure of the femoral diaphysis. The FGPB was manufactured from Ti-6Al-4V powder using the selective laser melting (SLM) technique. The morphological parameters, permeability and mechanical properties of FGPB samples were measured and compared with those of the biomaterials with uniform porous structures based on the same type of the unit cell. The FGPB exhibited a low density (1.9 g/cm3), a moderate Young's modulus (10.44 GPa), a high yield stress (170.6 MPa), a high maximum stress (201 MPa) and favorable ductility, being superior to the biomaterials with uniform porous structures in comprehensive mechanical properties. In addition, digital image correlation (DIC) and finite element (FE) simulation were used to unravel the mechanisms governing the deformation and yielding behavior of these biomaterials particularly at the strut junctions. Both DIC and FE simulations confirmed that the deformation and yielding of the FGPB occurred largely in the load-bearing layers but not at the interfaces between layers. Defect-coupled FE models based on solid elements provided further insights into the mechanical responses of the FGPB to compressive loads at both macro- and micro-scales. With the defect-coupled representative volume element model for the FGPB, the Young's modulus and yield stress of the FGPBs were predicted with less than 2% deviations from the experimental data. The study clearly demonstrated the capabilities of combined experimental and computational methods to resolve the uncertainties of the mechanical behavior of FGPBs, which would open up the possibilities of applying various porosity variation strategies for the design of biomimetic AM porous biomaterials. STATEMENT OF SIGNIFICANCE: Functionally graded bone scaffolds significantly promote the recovery of segmental bone defect. In the present study, we present a step-wise topological design of functionally graded porous biomaterial (FGPB) to mimic the structure of the femoral diaphysis. The Ti-6Al-4V FGPB exhibited a superior combination of low density, moderate Young's modulus, high yield stress and maximum stress as well as favorable ductility. The biomechanical performance of FGPB was studied in both macro and micro perspectives. The defect-coupled model revealed the significant yielding in the load-bearing parts and the Young's modulus and yield stress of the FGPBs were predicted with less than 2% deviations from the experimental data. The superiority of combined experimental and computational methods has been confirmed.

Fabrication of Biomedical Prototypes with Locally Controlled Properties Using FDM

Composite Modeling and Analysis for Fabrication of FDM Prototypes with Locally Controlled Properties

Numerical Simulation and Printability Analysis of Fused Deposition Modeling with Dual-Temperature Control

Effect of Processing Conditions on the Bonding Quality of Fdm Polymer Filaments

Predicting Mechanical Properties of Polymer Materials Using Rate-Dependent Material Models: Finite Element Analysis of Bespoke Upper Limb Orthoses

Modeling of Bond Formation Between Polymer Filaments in the Fused Deposition Modeling Process

An Accurate Finite Element Approach for Programming 4D-Printed Self-Morphing Structures Produced by Fused Deposition Modeling

Elasto-Plastic Mechanical Modeling of Fused Deposition 3D Printing Materials

Optimization of fused deposition modeling parameters to fabricate morphogenesis light weight structure with high tensile and compression strength

Effects of printing parameters of fused deposition modeling on mechanical properties, surface quality, and microstructure of PEEK

Mechanical characterization of biocompatible PEEK by FDM

A Hierarchical Nano to Micro Scale Modelling of 3D Printed Nano-Reinforced Polylactic Acid: Micropolar Modelling and Molecular Dynamics Simulation

Numerical Simulation and Experimental Study Regarding the Cross-Sectional Morphology of PEEK Monofilament Deposition During FDM-Based 3D Printing

Characterization for elastic constants of fused deposition modelling-fabricated materials based on the virtual fields method and digital image correlation

Improving Mechanical Performance of Fused Deposition Modeling Lattice Structures by a Snap-Fitting Method

Prototypes for Bone Implant Scaffolds Designed via Topology Optimization and Manufactured by Solid Freeform Fabrication

Topological design, permeability and mechanical behavior of additively manufactured functionally graded porous metallic biomaterials

A Simple Method for Fabricating Polymer/ceramic Functionally Graded Material Scaffold

3D printing of polycaprolactone-based composites with diversely tunable mechanical gradients via multi-material fused deposition modeling

Taguchi-Based Experimental Investigation and Modeling of 3D-Printed PEEK Parts as Biomedical Implants using Fused Deposition Modeling for Improving Mechanical Strength and Surface Quality