Abstract:A reciprocating extrusion process was developed to consolidate 6061-Al 2 O 3 p composites from mixed powders. The 6061 alloy powder was first dehydrated in a vacuum chamber at 450 °C and then mixed with 12.5 µm Al 2 O 3 powder in various volume fractions: 0, 5, 10, 20, and 30 pct. The mixed powders were hot pressed at 300 °C under a pressure of 300 MPa and finally extruded reciprocatingly 14 times at 460 °C. The results show that the composites were fully densified, with no sign of pores or oxide layers observable in the optical microscope. The Al 2 O 3 particles were distributed uniformly in the matrix. As compared with 6061 alloys, the composites demonstrated a smaller precipitation hardening and elongation, but exhibited a higher Young’s modulus and a larger work hardening capacity. The degradation of precipitation hardening was due to the loss of Mg, which reacts with Al 2 O 3 to form MgAl 2 O 4 . The large work-hardening capacity is attributable to the incompatibility between Al 2 O 3 and the matrix, which possibly generates more dislocations to harden the matrix. The composites had much higher friction coefficients and greater wear resistances than the 6061 alloy against steel disc surface. The friction coefficient of the 6061-30 vol pct Al 2 O 3 p composite was double that of the 6061 alloy and the wear resistance was 100-fold. As compared with similar composites reported previously, these composites possessed much higher elongation at the same strength level. A 30 vol pct Al 2 O 3 p still displayed an elongation of 9.8 pct in the T6 condition. All of these improvements are attributed to the merits, including full densification of the bulk, uniform dispersion of the Al 2 O 3 particles in the matrix, and strong binding between the Al 2 O 3 particles and the matrix resulting from reciprocating extrusion.

Preparation of Wearable Al-20pb Alloy by Powder Milling and Extrusion Densification

Preparing Al -Pb Alloy by Mechanical Milling and Canning Extrusion

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Al-Pb-Si-Sn-Cu bearing alloy synthesized by high energy ball milling and hot extrusion

Microstructure and Morphology of Al-Pb Bearing Alloy Synthesized by Mechanical Alloying and Hot Extrusion

Variation of mechanical properties and microstructures of Al-Pb mixed powder during mechanical milling

Microstructure Analysis for Al-Pb Alloy of Preparation in Powder Metallurgy Processing

Microstructure and Wear Properties of Al-Based Bearing Alloys Fabricated by Mechanical Alloying

Promoting the High Load-Carrying Capability of Al–20 Wt%sn Bearing Alloys Through Creating Nanocomposite Structure by Mechanical Alloying

MICROSTRUCTURE AND WEAR PROPERTIES OF Al-Pb-Cu ALLOY SYNTHESIZED BY MECHANICALLY ALLOYING

Powder preparation during ball milling and laser additive manufacturing of aluminum matrix nanocomposites: Powder properties, processability and mechanical property

Improvement of the Wear Behaviour of Al–Pb Alloys by Mechanical Alloying

Microstructure and wear properties of nanocomposite Al-Pb-Cu alloy cold-rolled onto steel matrix

Metallurgical reactions and tribological properties of self-lubricating Al-WS2 composites: Laser powder bed fusion Vs. spark plasma sintering

Tribological Properties of in Situ Fe3al-20 Wt% Al2o3 Composites

Microstructure and Wear Properties of Al–Pb–Cu Alloys Prepared by Mechanical Alloying

Study of 6061-Al2o3p Composites Produced by Reciprocating Extrusion

Manufacturing a TiAl Alloy by High-Energy Ball Milling and Subsequent Reactive Sintering

High Strength Al–Al2O3p Composites: Optimization of Extrusion Parameters

The Microstructure and Tribological Property of In-Situ Al2O3/Fe–25Al Composites in Argon Atmosphere

Preparation of Cbnp/Nicral Nanostructured Composite Powders by A Step-Fashion Mechanical Alloying Process