Abstract:Mo, Al2O3 single layer, Mo-Al2O3 granular cermet layer, Mo/Al2O3 tandem and an optimized Mo-Al2O3 multilayer coating with a double cermet layer configuration were deposited on stainless steel substrates by magnetron sputtering technique. The samples were annealed in vacuum at different temperatures ranging from 350 degrees C to 1000 degrees C for 2-5 It to evaluate their thermal stability. The spectral absorbance and thermal emissivity for the multi-layer selective coatings in the region of 1.3-25 mu m were 0.91-0.93 and 0.19-0.27, respectively, depending on heat treatment temperature. Increasing annealing temperature has more obvious influence on the rise of emissivity than the drop of spectral absorbance. The microstructure, surface morphology, composition distribution and diffusion for various films before and after high temperature aging were investigated employing scanning electronic microscopy, X-ray diffraction and X-ray photoelectron spectroscopy. Fe2O3, as a diffusion barrier between Mo layer and SS substrate, effectively holds back the presence of Mo2C and Fe2MoC complex phases. Al2O3 is a stable phase even at 1000 degrees C for 3 h. However, defects such as widened boundaries, cracks and holes, which could appear in Al2O3 layer when heated at higher temperature than 650 degrees C, will provide the paths of Mo diffusion. Two diffusion modes of Mo, including inner self-congregation of Mo inside the cermet layer and Mo infiltration through the Al2O3 layer in Mo/Al2O3 tandem at 800 degrees C for 5 h, were observed after annealing. (c) 2007 Elsevier B.V. All tights reserved.

Magnetron Sputtering High Temperature Mo-Al<sub>2</sub>O<sub>3</sub> Cermet Solar Selective Coatings

Magnetron sputtering high temperature Mo-Al2O3 cermet solar selective coatings

Microstructure and Spectral Selectivity of Mo–Al2O3 Solar Selective Absorbing Coatings after Annealing

Angular Solar Absorptance and Thermal Stability of Mo–SiO2 Double Cermet Solar Selective Absorber Coating

Improvement of Thermal Stability in the Solar Selective Absorbing Mo–Al2O3 Coating

THERMAL STABILITY OF Mo-SiO2 SOLAR SELECTIVE COATINGS AT HIGH TEMPERATURES IN AIR

Spectral Properties and Thermal Stability of Solar Selective Absorbing Alni-Al2o3 Cermet Coating

Optical Design and Co-Sputtering Preparation of High Performance Mo–SiO2 Cermet Solar Selective Absorbing Coating

Preparation and Spectral Properties of Solar Selective Absorbing MoSi2–Al2O3 Coating

The Investigation of Thermal Stability of Al/NbMoN/NbMoON/SiO 2 Solar Selective Absorbing Coating

Study of Selective Solar Absorption Cermet Coating (Invited)

Microstructure and Thermal Stability of Cu/Zr0.3Al0.7N/Zr0.2Al0.8N/Al34O60N6 Cermet-Based Solar Selective Absorbing Coatings

A New Solar Spectral Selective Absorbing Coating of SS–(Fe3O4)/Mo/TiZrN/TiZrON/SiON for High Temperature Application

SOLAR SELECTIVE ABSORBER BASED ON PARTICLE-SCATTERING EFFECT

High-temperature Air-Stable Solar Absorbing Coatings Based on the Cermet of MoSi2 Embedded in SiO2

High Performance Mid-Temperature Selective Absorber Based On Titanium Oxides Cermet Deposited By Direct Current Reactive Sputtering Of A Single Titanium Target

Optical Simulation and Experimental Optimization of Al/NbMoN/NbMoON/SiO2 Solar Selective Absorbing Coatings

Preparation and Optical Properties of Nb-NbN Multilayer Films As Solar Selective Absorptive Coatings

Double-layer solar absorber coating based on high entropy ceramic AlCrMoTaTiN: Structure, optical properties and failure mechanism

Stability of W-Al2O3 cermet based solar coating for receiver tube operating at high temperature

Optical Simulation and Preparation of Novel Mo/ZrSiN/ZrSiON/SiO 2 Solar Selective Absorbing Coating