Design and Practice of the Roasting System

YANG Heping,WANG Jianfang,N Qinxue

DOI: https://doi.org/10.3969/j.issn.1672-1152.2011.03.016

2011-01-01

Abstract:The technology and improving produce instance is introduced and main problem had been improved about the system of 109 m2 flowing roasting furnace in Zinc smelting company of Shangluo.

What problem does this paper attempt to address?

The Research Progress of Fluidized Roasting Technology in Aqueous Method of Zinc Production

XU Dong,ZHU Jun,WANG Zheng-min

DOI: https://doi.org/10.3969/j.issn.1003-5540.2007.06.007

2007-01-01

Abstract:This article briefly introduced the research progress of fluidized roasting technology in aqueous method of Zinc production,analyzed it in the aspects of the development of granulating,enhancing the efficiency of roasting furnace ebullition,the optimized roasting parameter and deactivation.Finally,it introduced the next research direction of fluidized roasting technology.
Research on Boiling Roasting Behavior of Complex Zinc Concentrate

Guo Yun,Zhang Fujian,Zhang Xuning,Zhang Nuonan,Yin Shijie,Zhou Bing,Zhu Lin

DOI: https://doi.org/10.3969/j.issn.1000-6532.2022.04.013

2022-01-01

Abstract:With the continuous scarcity of domestic zinc resources and the rapid changes in the market, the composition of zinc concentrates selected by zinc smelting companies has become more and more complex. High-silicon, high-copper, high-lead, and high-iron mineral sources have gradually become the norm. These high impurities ore seriously deteriorates the conditions of the fluidized roaster, which greatly affects the normal progress of the roasting process. In order for zinc smelting companies to achieve rapid development in the increasingly complex market competition, in addition to organizing production at the lowest cost, they also need to be able to adapt to various complex mineral sources, especially to be able to handle high value-added zinc concentrates. Therefore, this article systematically studies the behavior and influence of Cu, Pb, SiO2 and Fe, the key impurities in complex zinc concentrates, during boiling roasting, and aims to provide certain theoretical and practical guidance for zinc smelting enterprises to deal with complex zinc concentrates.
Study on the Migration and Release of Sulfur during the Oxidizing Roasting of High-Sulfur Iron Ore

Xiaojiao Chen,Na Zhao,Zhe Li,Zijian Wang

DOI: https://doi.org/10.3390/min14030276

IF: 2.5

2024-03-06

Minerals

Abstract:In China, most of the high-sulfur iron ores have not been fully developed and utilized due to the lack of breakthrough progress in the research on the sulfur migration and the desulfurization mechanism during the roasting process. This study will focus on revealing the release and fixation mechanisms of sulfur during the roasting process to achieve the transformation of desulfurization from terminal treatment to process control. Experimental results show that as the roasting temperature increases, the release rate of SO2 also increases, reaching the maximum release rate at 900 °C. Simultaneously, it is found that at the same roasting temperature, the release rate and amount of SO2 under the O2/N2 atmosphere is significantly greater than that under the pure N2 and air atmospheres. Meanwhile, X-ray diffraction (XRD) is utilized to explore the phase composition of the roasted product and the sulfur release mechanism. In addition, the adsorption energy, stability and electron transfer of SO2 on the CaO surface are calculated through density functional theory (DFT), and the optimal adsorption active site perpendicular to the O atom (O-top) is also determined. Finally, the sulfur fixing agent CaO is used to study the SO2 fixation mechanism. When the concentration reaches 10%, the sulfur fixation efficiency reaches more than 80%. Therefore, this work will present basic knowledge and systematic guidance for the sulfur migration and release of high-sulfur iron ore under the oxidizing roasting process.

geochemistry & geophysics,mineralogy,mining & mineral processing
Principle Analysis and Improvement for Sintering Fume Gas Cleaning System

Wansheng Zhao

2002-01-01

Abstract:The two sets of wet fuel desulphuring system with large equipments and easy process were used for sintering machine head at the Plant. In this paper, some improvement measures for wet process was discussed based on the desulphuring theory and working experience.
Study on Optimizing the Sintering Proportioning in Masteel

Jun Zhu

2012-01-01

Abstract:The high temperature sintering characteristics of ten kinds of iron ore fines in Masteel,such as assimilation,liquid phase fluidity,self-strength of bonding phase,the forming ability of SFCA and intergrowth bonding strength etc.were studied in this paper.Based on this,according to complementary principle of high temperature characteristics of iron ore fines,five groups of sintering proportioning optimization schemes were designed and sintering pot test was carried out,and good sintering effect was achieved for all schemes.The feasibility of sintering proportioning optimization method based on high temperature characteristics of iron ore fines was verified,and countermeasures were provided for Masteel to fully utilize iron ore fines resources,reduce proportioning cost and improve sinter quality.
Smelting Practice with Low Grade Iron Ore at 3200m~3 Blast Furnace of TISCO

YANG Xiao-dong,YAO Hong-xin,SUN Liang,LI Hong-fei

2013-01-01

Abstract:Aiming at the situation of iron ore grade declination for 3 200 m3 Blast Furnace of Tianjin Iron and Steel Group Company Limited (TISCO), the authors took measures such as enhancing management over charging raw material and fuel, optimizing burden structure, implementing foreman operation standardization system, adopting low silicon and low surfer smelting, maintaining rational actual blast flow rate and blowing kinetic energy and increasing top pressure. Consequently, long term stable, balanced and high efficient production was achieved at the blast furnace. The paper provides experience for smelting of large scale blast furnace with low grade iron ore.
PROCESS PRACTICE OF SMELTING WITH FERROUS COMPOUNDS AND STEEL SLAG

Zhigang Wang,Jiabin Ni,Xugang Jia,Guisheng Li,Dong Liu

DOI: https://doi.org/10.3969/j.issn.1671-3818.2011.05.010

2011-01-01

Abstract:A large number of ferrous compounds and steel slag were produced during steelmaking in Anyang Steel.In order to reduce the efflux and pollution of ferrous compounds,process practice of smelting was carried out with ferrous compounds and steel slag in 100t converter.By optimizing the adding mode and operation process,the consumption of steel material and slag was reduced,and operation of endpoint control and slag splashing protection was improved.Better social and economical benefits were obtained.
Temperature Co-optimization of Zinc Roasting Process Based on Fuzzy Synthetic Evaluation and Temperature Adjustable Margin

Zhenxiang Feng,Peng Ma,Yonggang Li,Bei Sun,Chunhua Yang

DOI: https://doi.org/10.1109/tfuzz.2024.3354835

IF: 12.253

2024-01-01

IEEE Transactions on Fuzzy Systems

Abstract:The roasting temperature is critical for enhancing product quality, reducing air pollution, and ensuring the long term operation of the zinc roasting process. However, optimizing the roasting temperature is challenging due to complex reaction mechanisms, feed composition fluctuations, and the coupling relationship with downstream processes. In this paper, a two level decision-making system for co-optimization of the roasting temperature is proposed. In the first level, a fuzzy synthetic evaluation model with variable-weight degradation degree is established to accurately evaluate the operating performance of the zinc roasting process. The evaluation results are used to design the basic setting rules that provide the basic temperature setting values. In the second level, a concept of temperature adjustable margin is introduced via sensitivity analysis of the pro cess model to evaluate the optimality of two roasters in the zinc roasting process. Based on the temperature-adjustable margin, the collaborative setting rules are designed to reasonably allocate the basic setting value to the two zinc roasters for optimizing the operating performance of the zinc roasting process. Finally, an industrial case study is presented to demonstrate the effectiveness of the proposed two-level decision-making system.

computer science, artificial intelligence,engineering, electrical & electronic
Thermal system design and optimization of an industrial silicon directional solidification system

Xu Ma,Lili Zheng,Hui Zhang,Bo Zhao,Cheng Wang,Fenghua Xu

DOI: https://doi.org/10.1016/j.jcrysgro.2010.10.102

IF: 1.8

2011-01-01

Journal of Crystal Growth

Abstract:This paper reports numerical investigation of multicrystalline silicon (mc-Si) ingot production using an industrial-scale directional solidification furnace capable of producing 500kg silicon ingot. Specific examination is made on thermal distribution, interface shape and velocity field. Evaluation is performed for the applicability of thermal system design to reduce carbon and oxygen impurity, improve crystal quality and enhance energy efficiency. The effects of gas flow, heater position and geometric configuration on temperature distribution are discussed as well to provide the essential knowledge for system optimization.
Research Progress and Prospect of Fluidized Bed Metallic Ore Roasting Technology: A Review

Shuangming Zhang,Tuo Zhou,Chaoran Li,Man Zhang,Hairui Yang

DOI: https://doi.org/10.1016/j.fuel.2024.132717

IF: 7.4

2024-01-01

Fuel

Abstract:Roasting of metallic ore is an important process in the metal smelting industry, in which the ore undergoes intense chemical changes to purify the metallic components. Fluidized bed technology has the advantages of strengthening mass and heat transfer, enhancing the chemical reaction rate, and at the same time the temperature uniformity in the furnace, which often makes it the preferred choice in metallic ore roasting. The development of fluidized bed roasting technology in the roasting of different types of metal ores with the latest advances in reaction kinetics, flow and heat transfer characteristics, and process optimization are introduced by taking three typical applications of fluidized bed roasting of pyrite, hematite, and zinc sulfide concentrate as examples. The future development trend in the context of carbon neutrality is prospected. Fluidized bed roasting technology is anticipated to be applied to more types of metallic ores. Meanwhile, it could be rapidly developed in flow and particle size optimization, pollutant control, and energy utilization.
An Experimental Investigation Oil Optimization of Technological Parameters of Sintering Process in Xuanhua Iron & Steel Co.

ZHANG Yu-zhu,LI Jie,XING Hong-wei,ZHANG Wei,YIN Hai-sheng

DOI: https://doi.org/10.3969/j.issn.1000-6532.2008.03.006

2008-01-01

Abstract:The technological parameters of sintering process are closely related with the quality of sintered ores.In order to establish optimal technological parameters of sintering process,a lot of experimental researches must be performed.Uniform design making the best of test point uniformity,uniform test times is less than orthogonal test.It can reduce the test investment,but still get near optimal technological parameters.According to the material conditions of Xuangang,this paper analyzes the effects different blending ratio of Iranian ore,basicity,carbon and MgO contents in sintering ore on the quality of sintered ore,and the optimal technological parameters are finally determined.
OPTIMIZATION AND EXPERIMENT OF HOT AIR TEA ROASTING MACHINE BASED ON CFD-DEM COUPLING

Kaixing ZHANG,He CHEN,Wenzhong WANG,Xiuyan ZHAO,Honghao LIU

DOI: https://doi.org/10.35633//inmateh-67-09

2022-08-31

INMATEH Agricultural Engineering

Abstract:A drum-type hot air tea roasting machine was designed to improve the quality of the roasted tea. The basic structure and working principle of the machine were studied theoretically and experimentally. The CFD-DEM coupled method and the Box-Behnken experimental design method were introduced to analyse the influence of the shape of the anti-skid bars and working rotating speed on the tea-roasting quality. The optimum combination of the working parameters with the height of the anti-skid bar is 30 cm, the figure of the anti-skid bar is 6, the rotating speed of the roller is 15 r/min, the broken-tea ratio is 2.15%, and the tea’s sensory appraisal index is 89.32. The comprehensive performance index was better.
Practice of energy-saving and discharge-reduction with the 400 m~2 sintering machine at Handan Iron and Steel

WEI Hang-yu,WANG Wen-sheng,LIU Wei,XU Jun-jie

DOI: https://doi.org/10.3969/j.issn.1009-9700.2012.03.007

2012-01-01

Abstract:The energy consumption by sintering amounts to about 13% of the overall energy consumption of the steel works,and the emissions of sulfur is the main pollution index of sintering production.A reduction of solid fuel for sintering by 0.5!,a dust content in the emitted gas < 12 mg / m 3,and a sulfur emission < 90 mg/m 3 were attainable for the 400 m 2 sintering machine by improving the fuel performance,stabilizing the equipment operation,and enhancing the dust-and sulfur-removing capacity.Good energy-saving and discharge-reduction effects thus resulted.
Industrial Experiment of Technique Optimization on IF Steel in RH Degasser

ZHANG Gui-fang,ZHU Hong-bo,CHEN Tian-ming

2010-01-01

Abstract:The production process was tracked and investigated by aiming the problem on RH refining process in the high carbon content and instability in IF steel production at Panzhihua Steel Works.Industrial experiments of technique optimization on IF steel in RH degasser was done by controlling technique psocesses of converter end point and the oxygen activity of molten steel and the slag composition and the oxygenation in the ladle,as well as the time of decarburization so on.Industrial experiments showed that the fluctuation range of the carbon content was small when IF molten steel left from RH degasser.Adding the carbon powder,the oxygen activity of decarburization molten steel was controlled at 121×10-6～318×10-6 and its average value was 230.1×10-6,it was lower than original process about 120×10-6,purity of molten steel was improved.Adopting the slag-modifier of high alkalinity adjusted the composition in the ladle,the content of CaO increased and the content of Al2O3 decreased and slag sticking phenomenon of inserted ducts were mitigated obviously.
Research on Technology of Blast Furnace Energy Saving and Optimization of Operation Principle

Shuangping Yang,Jun Sun

DOI: https://doi.org/10.4028/www.scientific.net/msf.610-613.419

2009-01-01

Abstract:By study the development situation of blast furnace smelting in china and the blast furnace operation system and technology, combined with production conditions of JISC BF, based on a large number of the production data, the comparison analysis test on JISC BF operation system and technology was did. Through continuously optimization and practice, the relatively suitable operation system and technology of JISC BF at present was explored, which Could reduce the coke ratio into furnace while increasing the coal injection ratio and making great economic effect.
Thermodynamic analysis and process optimization of zinc and lead recovery from copper smelting slag with chlorination roasting

Bei-kai ZHANG,Xue-yi GUO,Qin-meng WANG,Qing-hua TIAN

DOI: https://doi.org/10.1016/s1003-6326(21)65773-4

IF: 3.752

2021-12-01

Transactions of Nonferrous Metals Society of China

Abstract:An efficient chlorination roasting process for recovering zinc (Zn) and lead (Pb) from copper smelting slag was proposed. Thermodynamic models were established, illustrating that Zn and Pb in copper smelting slag can be efficiently recycled during the chlorination roasting process. By decreasing the partial pressure of the gaseous products, chlorination was promoted. The Box−Behnken design was applied to assessing the interactive effects of the process variables and optimizing the chlorination roasting process. CaCl2 dosage and roasting temperature and time were used as variables, and metal recovery efficiencies were used as responses. When the roasting temperature was 1172 °C with a CaCl2 addition amount of 30 wt.% and a roasting time of 100 min, the predicted optimal recovery efficiencies of Zn and Pb were 87.85% and 99.26%, respectively, and the results were validated by experiments under the same conditions. The residual Zn- and Pb-containing phases in the roasting slags were ZnFe2O4, Zn2SiO4, and PbS.

metallurgy & metallurgical engineering
PRACTICE AND EXPLORATION ON LOW COST OPERATION IN IRON-MAKING PROCESS

Liu Runsheng

DOI: https://doi.org/10.3969/j.issn.1006-3129.2011.04.006

2011-01-01

Abstract:According to the problems existing in the iron-making system,it carried out system theory critical path network to analyze and discuss these problems from plan,iron purchasing,quality,production,transportation,technical research and so on,it also provided resolving measures and explored low cost operation based on the actual situation.
Improvement of SIROX cleaning system

Guiping Wu,Jinqing Xu,Wei Ding,Mingxing Li,Feng Xie,Qisheng Chen,Xu Kong,Chengliang Yang,Hanying Li

DOI: https://doi.org/10.3969/j.issn.1672-6146.2016.04.011

2016-01-01

Abstract:Based on analyzing SIROX the tobacco expander of its pitfalls on cleaning system like poor water discharge, valve leakage, cleaning time consuming, etc., an improvement of its cleaning system is put forward as well as an optimization of its control mode. Furthermore, a new design of automatic drainage system of the cleaning pipe is presented as well as a real-time monitoring system. This set of system not only addresses quality issues like the over temperature of cylinder wall of the tobacco dryer and the abnormal fluctuation of the tobacco moisture after dryer, but also visualizes the valve leakage thus helps to improve the prompt maintenance of these devices. Observing the two-year operation in HCF, this system proves a high application value.
Application of response surface methodology for roasting optimization in composite roasting—Acid leaching vanadium extraction process

Xin Wang,Junyi Xiang,Guishang Pei,Lanjie Li,Qingyun Huang,Xuewei Lv

DOI: https://doi.org/10.1016/j.cherd.2021.06.017

IF: 4.119

2021-08-01

Chemical Engineering Research and Design

Abstract:The effective and environmentally friendly composite roasting with CaO/MgO was applied.The central composite design (CCD) and response surface method (RSM) were applied to optimize the roasting parameters in vanadium extraction process.The leaching efficiency of vanadium, phosphorus and manganese were evaluated.Composite roasting with CaO/MgO and leaching process is an environmentally friendly and simple technique in the treatment of vanadium slag which has been practiced using CaO and MgO as composite roasting additives. The recovery of vanadium is significantly influenced by the roasting parameters, viz., CaO/V2O5 mole ratio (x1), MgO/V2O5 mole ratio (x2), roasting temperature (x3), and holding time (x4). Therefore, the response surface method (RSM) and central composite design (CCD) were performed to model and optimize the roasting factors in this research. The results shown that the models for the dissolution of vanadium, phosphorus, and manganese show good concordance with the experimental data. Additionally, a multiple response simultaneous optimization using the desirability function was used to find the optimum roasting conditions for the leaching efficiency of vanadium, phosphorus, and manganese. The optimal results were obtained at x1 = 0.84, x2 = 0.40, x3 = 900 °C, and x4 = 1.89 h. Under these conditions, 90.87% vanadium, 13.64% phosphorus, and 48.61% manganese were leached, which were beneficial not only to the recovery of vanadium but also to the minimization of impurity element of phosphorus and the maximum recovery of manganese.<ol class="links-for-figure"><li><a class="anchor download-link u-font-sans" href="https://ars.els-cdn.com/content/image/1-s2.0-S0263876221002604-fx1_lrg.jpg">Download : Download high-res image (115KB)</a></li><li><a class="anchor download-link u-font-sans" href="https://ars.els-cdn.com/content/image/1-s2.0-S0263876221002604-fx1.jpg">Download : Download full-size image</a></li></ol>

engineering, chemical
Novelty on deep reduction roasting through removal of lead and zinc impurities from iron ore afore ironmaking

Sayaf Mustafa,Luo Liqun,Niyonzima Jean Christophe,Zheng Bo-tao,Wei Chen-xi,Lei Yanming,Longchuan Yang,Jia Ting,Mohammed Kabashi

DOI: https://doi.org/10.1016/j.powtec.2023.118857

IF: 5.64

2023-08-04

Powder Technology

Abstract:The novelty of deep reduction roasting is that iron (Fe) can be recovered to high degrees and a large proportion of zinc and lead impurities can be simultaneously removed. In this work, deep reduction roasting was performed at different temperatures, and phase changes were investigated during ironmaking. Haematite is the main Fe-bearing minerals in Xinjiang, China . It contains up to 91.35% iron and minor amounts of magnetite and iron silicate. The main form of zinc impurities is zinc oxide, and lead sulphide is present with low abundance. When the roasting temperature was 900 °C–1000 °C, the amount of coal reductant powder was 11%, the grade and recovery of Fe were 86% and 70% respectively. At 1050 °C–1200 °C, coal powder was added at C/O = 2.25 due to high coal powder consumption, and the magnetic separation concentrate products were obtained with an Fe grade of 86.34%–93.09% and Fe recovery rate of 75.06%–86.49%. In line with the requirement that the content of lead and zinc in iron concentrate powder products be less than 0.1%, the minimum contents of lead and zinc impurities in the magnetic separation concentrate were only 0.0084% and 0.048%, respectively. EPMA and EDS data revealed that after roasting, lead, zinc and sulphur impurities showed significant reductions and were absent from most microscopic areas. This study demonstrated that deep reduction roasting is suitable for removing lead and zinc impurities from iron ores before ironmaking.

engineering, chemical

Design and Practice of the Roasting System

The Research Progress of Fluidized Roasting Technology in Aqueous Method of Zinc Production

Research on Boiling Roasting Behavior of Complex Zinc Concentrate

Study on the Migration and Release of Sulfur during the Oxidizing Roasting of High-Sulfur Iron Ore

Principle Analysis and Improvement for Sintering Fume Gas Cleaning System

Study on Optimizing the Sintering Proportioning in Masteel

Smelting Practice with Low Grade Iron Ore at 3200m~3 Blast Furnace of TISCO

PROCESS PRACTICE OF SMELTING WITH FERROUS COMPOUNDS AND STEEL SLAG

Temperature Co-optimization of Zinc Roasting Process Based on Fuzzy Synthetic Evaluation and Temperature Adjustable Margin

Thermal system design and optimization of an industrial silicon directional solidification system

Research Progress and Prospect of Fluidized Bed Metallic Ore Roasting Technology: A Review

An Experimental Investigation Oil Optimization of Technological Parameters of Sintering Process in Xuanhua Iron & Steel Co.

OPTIMIZATION AND EXPERIMENT OF HOT AIR TEA ROASTING MACHINE BASED ON CFD-DEM COUPLING

Practice of energy-saving and discharge-reduction with the 400 m~2 sintering machine at Handan Iron and Steel

Industrial Experiment of Technique Optimization on IF Steel in RH Degasser

Research on Technology of Blast Furnace Energy Saving and Optimization of Operation Principle

Thermodynamic analysis and process optimization of zinc and lead recovery from copper smelting slag with chlorination roasting

PRACTICE AND EXPLORATION ON LOW COST OPERATION IN IRON-MAKING PROCESS

Improvement of SIROX cleaning system

Application of response surface methodology for roasting optimization in composite roasting—Acid leaching vanadium extraction process

Novelty on deep reduction roasting through removal of lead and zinc impurities from iron ore afore ironmaking