Abstract:Polybutene-1 (PB-1) always crystallizes into its metastable form II when cooled from a molten state because of its lower nucleation barrier, while the stable form I exhibits superior properties compared to form II, in particular, its resistance to creep and fracture. We investigated the polymorph selection of PB-1 during crystallization under high gas/supercritical fluid (SCF) pressure using a high-pressure chamber and differential scanning calorimeter. By applying pressurized gases/SCFs in PB-1 during crystallization, the obtained crystal form was changed from the kinetically favored metastable form II to the most stable form I′, which is desirable because of its outstanding mechanical properties. The formation of form I′ can also be promoted by increasing the crystallization temperature or by applying gases/SCFs with high solubility in PB-1. The enhancement of chain mobility under high-pressure gases/SCFs and at high crystallization temperatures plays a critical role in the polymorph selection. The increase in chain mobility results in an increase in entropy reduction and an increased surface free energy during nucleation. Therefore, the critical nucleus size required to achieve thermodynamic stability increases, and more entanglement would be needed to form the larger crystal nucleus, which has a greater effect on form II (which has a lower surface free energy under routine conditions) than on form I′. Furthermore, with increased CO2 pressure, we observed a greater reduction in the melting point in form II than in form I/I′. The increase in chain mobility would intensify the local melting in the crystal growth front, where the relaxation of the chains in the interface between the crystal and amorphous phase occurs stronger in the αc-mobile form II. Under high gas/SCF pressure, the formation of form I′ tends to dominate during the crystallization of PB-1, and the crystallization of the kinetically favored form II was suppressed because of the increased chain mobility.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acs.macromol.0c01986.DSC melting curves of PB-1 in three crystal forms measured at different CO2 pressures (PDF)This article has not yet been cited by other publications.

Co2-Induced Crystal Phase Transition from Form Ii to I in Isotactic Poly-1-Butene

CO2-Induced Phase Transition of Isotactic Poly-1-butene with Form III Upon Heating

Effect of pre-existed form I' on the phase transition of isotactic poly-1-butene form III under high pressure CO2

CO2-induced polymorphous phase transition of isotactic poly-1-butene with form III upon annealing

Controlling Crystal Phase Transition from Form II to I in Isotactic Poly-1-butene Using CO2

Crystalline transformation of isotactic polybutene-1 in supercritical CO2 studied by in-situ fourier transform infrared spectroscopy

Crystallization of Polybutene-1 into Forms I′, II, and III Under High Pressure CO 2 : In situ Synchrotron X-Ray Diffraction, WAXD Mapping, and DSC Investigations

Direct melt-crystallization of isotactic poly-1-butene with form I′ using high-pressure CO2

Elastic Stability of CO_{2} Phase I under High Temperature and Pressure

In Situ FT-IR Spectroscopic Study on the Conformational Changes of Isotactic Polypropylene in the Presence of Supercritical CO2

Effect of compressed CO2 on the melting behavior and βα-recrystallization of β-form in isotactic polypropylene

Effect of Crystalline Transformation on Supercritical CO2 Foaming and Cell Morphology of Isotactic Polybutene-1

Promotion of Form I′ in the Polymorph Selection of Polybutene-1 during Crystallization under High Gas/Supercritical Fluid Pressure via Enhancing Chain Mobility

Effect of crystalline transformation on supercritical CO 2 foaming and cell morphology of isotactic polybutene-1

Co2-Induced Crystallization of Isotactic Polypropylene by Annealing Near Its Melting Temperature

Investigation on phase transition from flow-induced oriented form II to I in isotactic polybutene-1 with in-situ microbeam X-ray diffraction technique

Utilization of supercritical CO2 for controlling the crystal phase transition and cell morphology of isotactic polybutene-1 foams

Chain dimension and crystallization temperature affected II-I transition of isotactic polybutene-1

High-temperature Relaxation Promoting Form II-to-form I Phase Transition of Polybutene-1

Change of lamellar morphology upon polymorphic transition of form II to form I crystals in isotactic Polybutene-1 and its copolymer

Chain dimension and crystallization temperature affect the II-I transition of isotactic polybutene-1