Abstract:Capillary electrophoresis (CE) is a separation technique that can be used as a sample pretreatment step in the analysis of ionic analytes (Grossman and Colburn 1992; Stewart et al. 2008). Compared with other separation technologies it can offer advantages such as higher speed and sensitivity, smaller injection volumes and reduced consumption of solvent and samples, the possibility of miniaturisation, and reduced cost (Issaq 2001; Jarmeus and Emmer 2008; Polesello and Valsecchi 1999; Wang 2005; Wee et al. 2008). CE is based on the difference of the electrical mobilities of molecules within a capillary tube filled with electrolyte solution. When an electrical field is applied between the two ends of a capillary and a sample is introduced at one end, analytes are separated as they migrate towards the other end under the influence of the electrical field. These separated analytes are detected near the outlet by methods such as optical or electrochemical techniques (Polesello and Valsecchi 1999; Guijt et al. 2004; Kappes and Hauser 1999; Kubaň and Hauser 2004, 2009; Kuhn and Hoffstetter-Kuhn 1993; Marzilli et al. 1997; Tanyanyiwa et al. 2002; Zemann et al. 1998). The signal from a detector is digitised and typically presented in the form of voltage versus time, i.e. an electropherogram. Peaks evident in an electropherogram typically correspond to analytes in the sample, and with optimisation of the system parameters, the peaks can usually be resolved sufficiently. Fig. 1 shows an example electropherogram of data obtained from a practical trial reported earlier (Petkovic-Duran et al. 2008) For analytical chemistry purposes, the operator's aim is to determine from the electropherogram what analytes are present and the corresponding concentrations. In this paper we assume that this is done by separating the task into two stages: Signal Processing, i.e., obtaining peak information from the electropherogram, and Pattern Matching, using this peaks' summary information to compare with established peak library of known chemicals. Whilst the process of identifying the peaks, removing the noise present and fitting curves for peak quantification is, to a large extent, done to-date manually by professionals, the operator would be greatly aided through fully automated techniques with little or no human input. This is particularly crucial for the development of field-deployable devices which could be operated by non-technical staff. Furthermore, automated signal processing techniques can allow results to be reproducible or consistent and can remove the subjectivity of a human evaluation. In addition, they can also detect features that may not

CE in a Nonuniform Capillary Modulated by a Cylindrical Insert, and Zone-Narrowing Effects During Sample Injection.

A Pressure-Driven Capillary Electrophoretic System with Injection Valve Sampling.

Sample plug induced peak splitting in capillary electrophoresis studied using dual backscattered interferometry and fluorescence detection

Microfluidic Picoliter-Scale Translational Spontaneous Sample Introduction for High-Speed Capillary Electrophoresis

Quantitative Sample Injection for Capillary Electrophoresis

Joule Heating Effects on Separation Efficiency in Capillary Zone Electrophoresis with an Initial Voltage Ramp.

Negative Pressure Pinched Sample Injection for Microchip-Based Electrophoresis.

Fast and simple sample introduction for capillary electrophoresis microsystems.

Elimination of suction effect in interfacing microchip electrophoresis with inductively coupled plasma mass spectrometry using porous monolithic plugs.

Improved High-Speed Capillary Electrophoresis System Using A Short Capillary and Picoliter-Scale Translational Spontaneous Injection

Microdialysis Hollow Fiber As a Macromolecule Trap for On-Line Coupling of Solid Phase Microextraction and Capillary Electrophoresis

Investigation of Separating Condition of Capillary Electrochromatography on 320 Mu M Internal Diameter Capillary Column

Pre-concentration of Non-Uniform Field Electrophoresis for Sample Introduction of Capillary Electrophoresis.

A Miniaturized Liquid Core Waveguide-Capillary Electrophoresis System with Flow Injection Sample Introduction and Fluorometric Detection Using Light-Emitting Diodes

Signal Processing Methods for Capillary Electrophoresis

Bundled capillary electrophoresis using microstructured fibres

Selectivity tuning in pressurized capillary electrochromatography with a zwitterionic monolithic column

Study on the influence of cross-sectional area and zeta potential on separation for hybrid-chip-based capillary electrophoresis using 3-D simulations.

Precise small volume sample handling for capillary electrophoresis

Getting the Best out of Capillary Electrophoresis and Capillary Electrophoresis-Mass Spectrometry by Quantifying Sources of Peak Broadening for Proteins Using Polyelectrolyte Multilayer Coated Fused Silica Capillaries

High-efficiency On-Line Concentration Technique of Capillary Electrochromatography.