Abstract:A novel microfluidic picoliter-scale sample introduction approach was developed by combining the spontaneous injection approach with a capillary electrophoresis (CE) system based on a short capillary and slotted-vial array. A droplet splitting phenomenon at the capillary inlet end during the spontaneous sample introduction process was observed for the first time. On the basis of this phenomenon, a translational spontaneous injection approach was established to reduce sample injection volumes to the sub-100 pL range. A versatile high-speed capillary electrophoresis (HSCE) system was built on the basis of this sample injection approach with separation performance comparable to or even better than those reported in microfluidic chip-based CE systems. The HSCE system was composed of a short fused-silica capillary and an automated sample introduction system with slotted sample and buffer reservoirs and a computer-programmed translational stage. The translational spontaneous sample injection was performed by linearly moving the stage, allowing the capillary inlet first to enter the sample solution and then removing it. A droplet was left at the tip end and spontaneously drawn into the capillary by surface tension effect to achieve sample injection. The stage was continuously moved to allow the capillary inlet to be immersed into the buffer solution, and CE separation was performed by applying a high voltage between the buffer and waste reservoirs. With the use of the novel system, high-speed and efficient capillary zone electrophoresis (CZE) separation of a mixture of five fluorescein isothiocyanate (FITC) labeled amino acids was achieved within 5.4 s in a short capillary with a separation length of 15 mm, reaching separation efficiencies up to 0.40 microm plate height. Outstanding peak height precisions ranging from 1.2% to 3.7% RSD were achieved in 51 consecutive separations. By extension of the separation length to 50 mm, both high-speed and high-resolution CZE separation of eight FITC-labeled amino acids could be obtained in less than 21 s with theoretical plates ranging from 163,000 to 251,000 (corresponding to 0.31-0.20 microm plate heights). The present HSCE system also allowed fast chiral separations of FITC-labeled amino acids under micellar electrokinetic chromatography (MEKC) mode within 6.5 s.

Combination of flow injection with capillary electrophoresis. Part 3. On-line sorption column preconcentration capillary electrophoresis system

Combination of flow injection with capillary electrophoresis. Part I. The basic system

On-line Concentration by Field-Enhanced Sample Injection with Reverse Migrating Micelles in Micellar Electrokinetic Capillary Chromatography for the Analysis of Flavonoids in Epimedium Brevicornum Maxim

Combination of Flow Injection with Capillary Electrophoresis

Combination of Flow Injection with Capillary Electrophoresis.

A Pressure-Driven Capillary Electrophoretic System with Injection Valve Sampling.

Combination of flow injection with capillary electrophoresis. Part 6.: A bias-free sample introduction system based on electroosmotic-flow traction

Miniaturized Capillary Electrophoresis System with Ultraviolet Photometric Detection Combined with Flow Injection Sample Introduction Using a Modified Falling-Drop Interface

Combination of flow injection with capillary electrophoresis. Part 2. Chiral separation of intermediate enantiomers in chloramphenicol synthesis

Developments in Flow Injection—Capillary Electrophoresis Systems

Capillary Electrophoresis System with Flow Injection Sample Introduction and Chemiluminescence Detection on a Chip Platform.

Development and Application of Capillary Electrophoresis-Electrospray Ionization Mass Spectrometry System Based on A Coaxial Sheath Flow Interface

Online Preconcentration Methodology That Realizes over 2000-Fold Enhancement by Integrating the Free Liquid Membrane into Electrokinetic Supercharging in Capillary Electrophoresis for the Determination of Trace Anionic Analytes in Complex Samples

Flow-Injection Online Sorbent Extraction Preconcentration for Graphite-Furnace Atomic-Absorption Spectrometry

Quantitative On-Line Concentration for Capillary Electrophoresis with Inkjet Sample Introduction Technique

Automated high-speed CE system for multiple samples

Automated sample preparation and analysis using a sequential-injection–capillary electrophoresis (SI–CE) interface

Simultaneous determination of trace amounts of nickel, copper and mercury by liquid chromatography coupled with flow-injection on-line derivatization and preconcentration

On-line Separation and Preconcentration in Flow Injection Analysis

A Miniaturized Liquid Core Waveguide-Capillary Electrophoresis System with Flow Injection Sample Introduction and Fluorometric Detection Using Light-Emitting Diodes

Microfluidic Picoliter-Scale Translational Spontaneous Sample Introduction for High-Speed Capillary Electrophoresis