Abstract:The article presents the results of studies of the process of obtaining granular materials from high-strength aluminum alloys of the Al - Zn - Mg - Cu system by centrifugation of the melt with ultra-high cooling rates of granules. The concept of a «steam jacket» is introduced, namely, a steam layer that occurs between the granule body and the cooling liquid, which prevents the intensity of heat removal and is an obstacle to increasing the crystallization rate due to the lower thermal conductivity of water vapor. It is established that the formation of a vapor layer always occurs due to the heating of the cooling liquid in contact with the melt drop to boiling temperatures and the transition of the cooler from the liquid phase to steam. The technology of increasing the rate of crystallization of granules due to the constant removal of the vapor layer is proposed. The removal (knocking down) of the vapor shell that occurs around the drop occurs due to the high speed of the drop movement in the cooling medium. Fundamentally important in the industrial implementation of this technology is not so much the design of the device for obtaining pellets by centrifugation of the melt, namely, the high required rotation speed of the spraying crucible of the device under consideration. The results of experimental data are presented to determine the necessary rotation speed of the perforated cup, which ensures the creation of a sufficient initial velocity of the drop movement, leading to a constant churning of the «steam jacket». It is determined that an increase in the rates of heat removal from the crystallized granules and, as a result, an increase in the crystallization rate leads to an increase in the strength characteristics of granular aluminum alloys of the Al-Zn-Mg-Cu system. In particular, in the production of pressed semi-finished products from alloys of the Al-Zn-Mg-Cu system, such as B95, B96c. the increase in the strength characteristics of the material of the press products is up to 15 % compared to the same granular materials obtained by traditional methods with industrial crystallization rates of melt droplets. It is established that this method, based on the removal of the vapor layer around the formed granule, is the only possible one for further increasing the cooling rate and, as a result, the crystallization rate. Reducing the size of granules to the size of powders leads to serious technological problems in the further consolidation of granules and, in fact, is a dead end branch of the further development of granulation methods.

Investigation of Granulated Metal Fabricated by Short Flow Casting Technology

Experimental investigation on granulation characteristics and waste heat recovery of molten slag in gas quenching dry granulation technique

Computational Fluid Dynamics Numerical Simulation on Flow Behavior of Molten Slag–Metal Mixture over a Spinning Cup

Investigation on Unsteady Phase-Change Heat Transfer Characteristics of Centrifugal Granulated Particles

Investigation into the sheet metal forming process using solid granules medium with graphite powder addition

A Study and Application of Batcher Drip Nozzle Used for Casting Metal Grains

Investigation on Heat Transfer in Molds with Different Water-Cooling Structures Under Billet High-Speed Continuous Casting

Measurement and observation of the filling process of steel castings

Research on Magnetic Floating Horizontal Continuous Casting Process (MFCC) for Nearly Net-Shape Molten Metal Afterheat Billet

Investigation of the features of crystallization of granules of high-strength aluminum alloys of the Al-Zn-Mg-Cu system at ultra-high cooling rates

Application of Graphite Electrode Plasma Heating Technology in Continuous Casting

The Heat Transfer Characteristics of Semi-molten Wide Sieving Dilute Phase Particles Between Vertical Heating Surfaces

A New Steel Teeming Technology by Using Electromagnetic Induction Heating System in Ladle

Controlled Film Flow in Granulation of Metals for the Development of Amorphous Superhard and Functionally Unique New Materials

Energy saving from furnace slag: Study on centrifugal granulation characteristics of the rotating cup

Design of Automatic Flux Feeder for Continuous Casting Mould of Fixed Size Plate Blank

Characteristics of flight trajectory and heat transfer of liquid steelmaking slag droplet during air quenching granulation process

Optimizing Heat Transfer Characteristics in Dry Centrifugal Granulation: Impact of Particle Population Trajectory and Cooling Strategies

Granulation performance by hybrid centrifugal-air blast technique for treatment of liquid slag

High-temperature Analogy Experimental Investigation on Dry Granulating Characteristic of Rotating Disk for Waste Heat Utilization of Molten Slag

Heat Transfer Characteristics of High-Temperature Particle Population in Ultra-Dilute Phase: Particle-fluid-surface Heat Transfer During Falling