Abstract:The article presents the results of studies of the process of obtaining granular materials from high-strength aluminum alloys of the Al - Zn - Mg - Cu system by centrifugation of the melt with ultra-high cooling rates of granules. The concept of a «steam jacket» is introduced, namely, a steam layer that occurs between the granule body and the cooling liquid, which prevents the intensity of heat removal and is an obstacle to increasing the crystallization rate due to the lower thermal conductivity of water vapor. It is established that the formation of a vapor layer always occurs due to the heating of the cooling liquid in contact with the melt drop to boiling temperatures and the transition of the cooler from the liquid phase to steam. The technology of increasing the rate of crystallization of granules due to the constant removal of the vapor layer is proposed. The removal (knocking down) of the vapor shell that occurs around the drop occurs due to the high speed of the drop movement in the cooling medium. Fundamentally important in the industrial implementation of this technology is not so much the design of the device for obtaining pellets by centrifugation of the melt, namely, the high required rotation speed of the spraying crucible of the device under consideration. The results of experimental data are presented to determine the necessary rotation speed of the perforated cup, which ensures the creation of a sufficient initial velocity of the drop movement, leading to a constant churning of the «steam jacket». It is determined that an increase in the rates of heat removal from the crystallized granules and, as a result, an increase in the crystallization rate leads to an increase in the strength characteristics of granular aluminum alloys of the Al-Zn-Mg-Cu system. In particular, in the production of pressed semi-finished products from alloys of the Al-Zn-Mg-Cu system, such as B95, B96c. the increase in the strength characteristics of the material of the press products is up to 15 % compared to the same granular materials obtained by traditional methods with industrial crystallization rates of melt droplets. It is established that this method, based on the removal of the vapor layer around the formed granule, is the only possible one for further increasing the cooling rate and, as a result, the crystallization rate. Reducing the size of granules to the size of powders leads to serious technological problems in the further consolidation of granules and, in fact, is a dead end branch of the further development of granulation methods.

Controlled Film Flow in Granulation of Metals for the Development of Amorphous Superhard and Functionally Unique New Materials

Research Progress of Granular Flow and Fluidization Behavior of Coarse Cohesive Particles

Investigation of the features of crystallization of granules of high-strength aluminum alloys of the Al-Zn-Mg-Cu system at ultra-high cooling rates

Dynamic Densification of Wet Granular Materials in Continuous Dense Flows under Gravity

Development of technology for the production of granular materials with an ultrafine structure from high-strength aluminum alloys

Analysis of features of heat transfer processes during crystallization of aluminum alloy granules in aqueous and water-vapor media

Controlling grain structure in metallic additive manufacturing using a versatile, inexpensive process control system

Powder-size driven facile microstructure control in powder-fusion metal additive manufacturing processes

Investigation of Granulated Metal Fabricated by Short Flow Casting Technology

Grain structure control during metal 3D printing by high-intensity ultrasound

INCREASING OF THE HEAT AND MASS TRANSFER PROCESSES EFFICIENCY WITH THE APPLICATION OF NON-UNIFORM FLUIDIZATION

An overview of powder granulometry on feedstock and part performance in the selective laser melting process

Microscale Heat and Mass Transfer and Non-Equilibrium Phase Change in Rapid Solidification

Nanophase And Ultrafine-Grained Powders Prepared By Mechanical Milling: Full Density Processing And Unusual Mechanical Behavior

Increasing the efficiency of transfer processes when using inhomogeneous fluidization

Metal vapor micro-jet controls material redistribution in laser powder bed fusion additive manufacturing

The research of the processes of formation of porous non-ferrous metals

Metallurgy and Solidification Microstructure Control of Fusion-Based Additive Manufacturing Fabricated Metallic Alloys: A Review

Grain refinement of stainless steel in ultrasound-assisted additive manufacturing

Nucleation, growth and breakage phenomena in agitated wet granulation processes: a review

Development of Advanced Technologies for the Production of Innovative Materials with a Submicrocrystalline Structure by Methods of Severe Plastic Deformation