Abstract:The C-band deflecting cavity designed last year is finished. In this paper, the RF measurement of the cavity is introduced. After tuning, it works well at 5.712GHz with a coupling factor degree around 1.05. And we measured the electromagnetic field with bead-pull method. The flatness of the magnetic field is around 0.9, which is not ideal but meet the requirements of the bunch length measurement. And we propose a method of tuning to make sure both frequency and field flatness. INTRODUCTION The C-band deflecting cavity designed last year for the measurement of ultra-short electron beams is finished. It’s a standing wave RF deflecting structure consisting of 3 cells. This cavity is designed to operate at a frequency of 5.712GHz. In the second section of the paper, the design of the deflector is briefly introduced. RF measurement results are shown in the third part. And a new tuning method is discussed in the fourth part. RF DEFLECTOR DESIGN In our case, we choose a 3-cell SW structure to meet the required transverse deflecting voltage Vdef=1MV. The working mode is TM110 mode and π-mode. The 3D-model draw by CST is shown in Figure 1. Figure 1: 3D-design of the deflector. The main part of the model is composed of several cylinders. The radii of the cells are determined by both the frequency and magnet field flatness. And the length of central cell is determined by the working mode while the length of the end cells is determined by the results of particle dynamics[1]. In order to make sure the polarization direction not changed while two cell coupled, two end cells are slotted on the edges which are perpendicular to the direction we put the coupler. According to the discussion above, the dimensions of the cavity are shown in figure 2 and table 2. Figure 2: 3D-design of the deflector. Table 1: Dimensions of the RF Cavity Dimensions Value(mm) rm 30.85 dm 21.49 re 30.61 de 10.93 t 4.76 rb 8 rslot (not shown in figure 2) 3.5 According to the dimensions, it’s easy to get the cavity parameters such as the transverse shunt impedance. And table 3 shows the main parameters of the RF cavity. With 1 MW input power, the deflecting voltage can be 1.19 MV. Table 3: Cavity Parameters Parameters Value Q0 9003 RT/Q(MΩ) 156 RT(MΩ) 1.42 P(MW) 1 Vdef(MV) 1.19 ___________________________________________ *Work supported by NSFC 11375098 and 11327902 #jxp14@mails.tsinghua.edu.cn MOPMR060 Proceedings of IPAC2016, Busan, Korea ISBN 978-3-95450-147-2 386 C op yr ig ht © 20 16 C C -B Y3. 0 an d by th e re sp ec tiv e au th or s 06 Beam Instrumentation, Controls, Feedback and Operational Aspects T03 Beam Diagnostics and Instrumentation In table 3, we are more concerned about RT/Q which has little change after machining. And we can evaluate the real deflecting voltage by measuring the quality factor Q0 by equation 1

Measurement for the Kanthal Alloy Used for Collinear Load and the S-Band Load Design

Accurate Evaluation of RF Coil-Tissue Interactions Using a Hybrid FDTD-MoM Method

Study on Electro-Thermo-Mechanical Responses of Bonding Wires Arrays Used for the Package Design of Ldmosfet-Based Rf Amplifier

A Broadband Permeability Measurement of Fetan Lamination Stack by the Shorted Microstrip Line Method

Attenuation Measurement of the Dielectric Rod Using Parallel Strips with a Resonable Field Environment

Methodology for Measurement of Submicron Metallic Wire's Local Electrical Conductivity by Applying Four-points AFM Probe Technique

Electromagnetic Field and Temperature Field Analysis of Coil Type Lead-Bismuth Electromagnetic Flowmeter

Ghz Microwave Permeability of Cofezr Amorphous Materials Synthesized by Two-Step Mechanical Alloying

Structure Modification of M-AFM Probe for the Measurement of Local Conductivity

C-Band Deflecting Cavity for Bunch Length Measurement of 2.5 MeV Electron Beam

Design, fabrication and low-power RF measurement of an X-band dielectric-loaded accelerating structure

Development and Measurements of A Technological Cavity for 350mhz High Current Proton Rfq

Study of magnetic alloy cores for HIRFL-CSRm compressor cavity

Modeling and measurement of lead tip heating and resonant length for implanted, insulated wires

Design and Cold Measurements of a Coupled RFQ-SFRFQ Cavity

Coupler Conditioning and High Power Testing of ADS Spoke Cavity

MEASUREMENTS OF FINE STRUCTURES IN THE LEAD-BISMUTH EUTECTIC ALLOY MELTS BY DIFFERENTIAL SCANNING CALORIMETRY

Optimization and Measurement for an Electron Side-Coupled Linac with Longitudinally Off-Axis Coupling Cavities

A compensated flanged coaxial tester for shielding effectiveness measurement

RF-thermal-structural-RF coupled analysis on the travelling wave disk-loaded accelerating structure

Inline Measurement of Acoustoelastic Coefficient in Conductive Sheet Material With Electromagnetic Loading System