Abstract:Red mud (RM) has drawn a lot of attention in the search for potential uses in the production of sintered artificial aggregate from industrial waste products. The main objective of the study is to produce an RM-based sintered artificial aggregate (SAA), with several blends (binary, ternary, and quaternary) using various industrial wastes. This study includes assessing the mechanical and physical properties of SAA as well as the sintering parameters in order to determine the appropriate material mix ratio. To achieve these objectives, a comprehensive experimental approach was adopted. A total of 35 different mixtures were formulated by incorporating various industrial wastes as binders and sintering additives. The green pellets were preheated at 105°C for 24 hours, and consecutively sintered at different temperatures, namely 700°C, 900°C, 1100°C, and 1150°C with a duration of 30 minutes. A compressive strength test was performed in order to find the mechanical property of SAA similarly water absorption and bulk density tests were conducted to find the physical properties of SAA. To characterize the SAA, scanning electron microscope analysis (SEM), X-ray diffraction (XRD) and energy dispersive X-ray analysis were conducted, and also data analysis was performed using Artificial Neural Network (ANN) tools, yielding accurate predictions. Successfully best compressive strength low water absorption SAA was produced. The best material weight mix ratio for the production of SAA was identified as (A18) RM: Fly Ash: Waste Glass Powder; 78:10:12. Out of all blends the ternary blend (A18) SAA exhibited impressive properties after 30 minutes of sintering at 1150°C: high compressive strength of 22.92 MPa, water absorption of 4.26%, and bulk density of 1296.12 kg/m3. This was made possible by the high amount of Al2O3, SiO2, in the combination of fly ash, and waste glass powder with RM. SEM and XRD analysis also confirmed that the (A18) SAA achieved the best compressive strength, and low water absorption due to turning the surface and core area into a solid, reduced internal pores and formed quartz, and hematite phases. The findings of this study serve as a foundation for future work and pave the way for the development of sustainable construction materials.

Utilization of red mud for the preparation of lightweight aggregates

Effects of Red Mud on Workability and Mechanical Properties of Autoclaved Aerated Concrete (AAC)

Investigation on the fabrication of lightweight aggregate with acid-leaching tailings of vanadium-bearing stone coal minerals and red mud

Utilization of Red Mud with High Radiation for Preparation of Autoclaved Aerated Concrete (AAC): Performances and Microstructural Analysis

Investigation of hierarchical porous cold bonded lightweight aggregates produced from red mud and solid-waste-based cementitious material

Performance of glass-ceramic-based lightweight aggregates manufactured from waste glass and muck

Upcycling of lime mud into lightweight artificial aggregates through the crushing technique

Production of lightweight aggregates from bauxite tailings for the internal curing of high-strength mortars

Use of bauxite tailing for the production of fine lightweight aggregates

Material properties and environmental implications of red mud solidified with blast-furnace slag, silica fume, and sodium hydroxide

Experimental Investigation on Red Mud from the Bayer Process for Cemented Paste Backfill

Utilization of red mud in high-performance grouting material for semi-flexible pavement

Efficient Utilization of Waste Marine Clay for Fine Aggregate to Develop Sustainable and Cost-Effective Strain-Hardening Cement-Based Composites

Effect of Red Mud on Mechanical Properties of Loess–Containing Aluminosilicate Based Cementitious Materials

Recycling of the end-of-life lightweight aggregate concrete (LWAC) with a novel approach

Preparation mechanism and properties of thermal activated red mud and its geopolymer repair mortar

Lightweight aggregate: a sustainable alternative for reuse of sawdust waste in the industrial process

Development of red mud based sintered artificial aggregates with various industrial wastes

The synergistic hydration mechanism and environmental safety of multiple solid wastes in red mud-based cementitious materials

Glass and glass-ceramics from red mud tailings: Understanding the evolution mechanism

Manufacturing non-sintered ceramsite from dredged sediment, steel slag, and fly ash for lightweight aggregate: production and characterization