Abstract:Objective In order to fit the anatomical bone form,different size of femoral and tibial part of fixed-bearing modular knee prosthesis are often used.This study investigates contact stress of different matching groups by finite element analysis(FEA),with the aim of learning the potential risks of different matching groups of knee prosthesis.Methods The size 3 cochrome femoral prosthesis,size 2.5,3 and 4 titanium tibial tray and 10 mm polyethylene insert of Depuy PFC Sigma fixed-bearing knee prosthesis was selected for study.Experimental group: size 3 femoral prosthesis with size 2.5(3/2.5) and 4(3/4) tibial prosthesis.Control group: size 3 femoral prosthesis with size 3 tibial prosthesis(3/3).Finite element models were constructed respectively in two groups.Max.equivalent stress of simulative standing,flat-floor walking,walking upstairs with knee flexion of 0°,10°,20°,30°,45°,60°and 75°were studied.The difference of equivalent stress between experimental group and control group was compared.Results The Max.equivalent stress of experimental group(3/2.5 or 3/4) was higher than that of control group(3/3).In the simulative standing mode,there was no significant difference between 3/3 and 3/2.5 pairing(P0.05) and there was significant difference between 3/3 and 3/4 pairing(P0.05).In the simulative flat-floor walking mode,there was significant difference between 3/3,3/2.5 and 3/4 pairing among different angles from 0°to 75°(P0.05).In the simulative walking upstairs mode,there was significant difference between 3/3,3/2.5 and 3/4 pairing among different angles from 0°to 30°(P0.05),yet no significant difference was found within the range of 45°to 75°(P0.05).Conclusions The Max.equivalent stress of contact area at different motion angle and status of experimental group(3/2.5 or 3/4) increases due to different sizes of femoral and tibial prosthesis,which may lead to increased wearing of polyethylene insert.

Finite Element Analysis of a Six-Component Force Sensor for the Trans-Femoral Prosthesis.

Design and static calibration of a six-dimensional force/torque sensor for minimally invasive surgery

A Novel Tactile Sensing Array with Elastic Steel Frame Structure for Prosthetic Hand.

Finite Element Modeling of the Contact Interface Between Trans-Tibial Residual Limb and Prosthetic Socket.

Three-dimensional Finite-Element Analysis and Biomechanical Design of Femoral Prosthesis

Design and fabrication of a six-dimensional wrist force/torque sensor based on E-type membranes compared to cross beams

Finite Element Analysis of Fixed-Bearing Knee Prosthesis with Different Size of Femur and Tibia Parts

Elastic Body Analysis of Foot Force Sensor on a Three-Limb Robot

HUMAN FEMUR FINITE ELEMENT ANALYSIS BASED ON CT SCAN DATA

Design and Optimization of Elastic Structure of Miniature Six-Dimensional Force/Torque Sensor

Design of a novel six-axis force/torque sensor based on strain gauges by finite element method

Finite Element Analysis of A Retrieved Custom-Made Knee Prosthesis

Design and analysis of a novel isotropic six-component force/torque sensor

A Quasi-Dynamic Nonlinear Finite Element Model to Investigate Prosthetic Interface Stresses During Walking for Trans-Tibial Amputees

Development of the Force Detecting Liner for Total Knee Arthroplasty

Development of a Flexible Meniscus Sensor for Detection of Force Distribution in Knee Arthroplasty

Strain Analysis of Six-axis Force/Torque Sensors with Y-shaped Crossbeam

Design of Six-Axis Force Sensor and Analysis of Its Experimental Data

Finite element analysis of in vivo tibio-femoral contact features with menisci

Design and analysis of parallel six-dimensional force sensor based on near-singular characteristics

A Three-Dimensional Finite Element Model Constructed Using Magnetic Resonance Images of a Knee