Abstract:A flat-field holographic concave grating can be the only optical element in a spectrometer. If the mutually compensating roles of the concave grating and the spectrometer are taken into account, the difficulty of fabricating concave grating can be reduced. When the holographic method is used to make concave gratings, it is very difficult to fix precisely the spatial distances between the two recording points and the vertex of concave gratings. In like manner, it is also difficult to fix precisely the location of the entrance slit or the CCD in using concave gratings in spectrometers. In other words, during the fabrication stage and the end-use stage of concave gratings, there are inevitable errors between the practical system structure parameters and the theoretical ones. The authors name them fabrication structure errors and end-use structure errors, respectively. Numerical simulation indicates that these two classes of errors will seriously deteriorate the spectral image quality. At present, there are few references describing the elimination of the fabrication and end-use errors of concave gratings. In this paper, a concave grating used in a compact chromatograph is analyzed as an example. By performing numerical simulations that take both fabrication structure parameters and end-use structure parameters into consideration, we found that in a large neighborhood around the design point, the two sets of parameters can mutually compensate. This means that even both sets are away from the optimized design points, as long as proper compensations are made, the spectral image quality of the spectrometer can be as good as designed. In other words, on the one hand, for a specific concave grating that has been made with some fabrication structure errors, we can move the CCD to find an appropriate location where the spectral image quality is as good as designed; On the other hand, for a decided end-use system which has some end-use structure errors, we can adjust the fabrication structure to make concave gratings that will generate good spectral images in this end-use system. The experiment results show that this method is an effective way to adjust the optical system for grating fabrication. The authors also give experimental results that agree with simulation results. Such compensation can reduce both the alignment difficulty and the required precision of fabrication structure parameters of concave gratings. It could also give theoretical guidance to the design and assembly of spectrometers.

Fabrication Error Model and Near Field Beam Modulation Analysis for Phase Step Diffractive Gratings

Design of Off-angle Beaming Device Based on Subwavelength Metal Thin Film Microstructure

Fabrication Error Analysis of Nonperiodic-Multilayer-dielectric Gratings

Simulation Method for Analyzing Mechanical Long-Period Fiber Gratings under High Birefringence

Error Analysis of Gratings in Optical Pickup Heads

Effects of Fabrication Errors on MTF and Diffraction Efficiency for Binary Optical Lens

Surface Error Modeling of Mounted Large Optics in High Power Laser System

A Method of Fabricating Wide Spectrum Flat-Field Concave Grating with Compensation Concave Lens

Refined Spectral Regulation of Chirped Fiber Bragg Gratings

Analysis for Fabrication Errors of Arrayed Waveguide Grating Multiplexers

Numerical Simulation and Experimental Demonstration of Error Compensation Between Recording Structure and Use Structure of Flat-Field Holographic Concave Gratings

Influence of Fabrication Error on the Characteristics of a 2-D Photonic-Crystal Cavity

Far Field Analysis after Chirped Pulse Passing through a Misalignment Tiled-Grating Compressor

The Impact of Fabrication Errors on A Flat-Top Grating-Based Planar Waveguide Demultiplexer

Fabrication of Gratings with Low Spacing Error by the Dual-Beam Exposure System with Spherical Lens

Wavefront Error Modeling and Control Method for Large Aperture Optical Unit in High Power Solid-State Laser

Application of Broad-Beam Scanning Exposure to Fabricate Low-Wavefront-error Holographic Gratings

Method for Fabricating Large-Area Gratings with a Uniform Duty Cycle Without a Spatial Beam Modulator

Wavefront Aberration of Plane Diffraction Gratings Fabricated in A Lloyd'S Mirror Interferometer

Metal/multilayer-dielectric Coated Grating for Chirped Pulse Amplification Laser System

Improvement of measurement error for modified coherent gradient sensing