Abstract:This article focuses on realizing wideband compartment shielding in the shielding can packages of miniaturized high-speed chip modules and circuits. Because the conventional diaphragms with a low profile are difficult to cope with the high-order mode interference and evanescent wave interference, a new “meta-diaphragm,” which is based on the single-negative (SNG) metamaterial, is proposed to address these inherent problems. It is demonstrated that benefitting from the large propagation attenuation introduced by the proposed meta-diaphragm, a good shielding performance can be achieved at the first higher order resonance mode. Moreover, by elaborately embedding resistors in the meta-diaphragm, the additional interferences at other resonance frequencies can be significantly suppressed. Furthermore, the structure of the meta-diaphragm is optimized with two approaches: evolving from the single-band SNG structure to the double-band one and integrating with the parasitic patches. The two approaches enable its independent controlling ability at different frequency ranges and enhancement of low-frequency shielding performance. Based on the proposed technique, an experiment is implemented to suppress the resonance-dominated interference between the passive traces in a shielding can. The result agrees well with those from theoretical prediction. The final experimental shielding can’s profile and width are 5 and 20 mm, respectively; the meta-diaphragm’s profile is only 1.5 mm, i.e., < 1/3 of shielding can’s profile, and its electrically length is only 3 mm, i.e., $0.1\lambda _{0}$ at 10 GHz, and the measured (simulated) meta-diaphragm can significantly suppress radio frequency interference (RFI) within 10.2–17 GHz (10–16.9 GHz) and realize $< -33.5$ dB ( $< -40$ dB) coupling within 100 kHz–18 GHz (dc-to-20 GHz). The miniaturized dimension and wideband results indicate that our proposed technique could meet the compartment shielding requirement of a series of miniaturized packages in the practical radio frequency (RF) chip modules and circuits.

Design and Consideration of Wafer Level Micropackaging for Distributed RF MEMS Phase Shifters

Novel Millimeter-Wave Power Combining Utilizing Wafer Level Packaging Technology

Tightly-integrated chip packaging structure and phased array radio frequency transceiving device formed by tightly-integrated chip packaging structure

A Novel Wafer Level Package Strategy For Rf Mems

A Pre-Shaped Wafer Level Packing Strategy for Rf Mems

An Ultra Broadband Passive Vector Modulator Phase Shifter

Design and Fabrication of a TR Microsystem in Ka Band with Si-Based 3D Heterogeneous Integration

A Bulk Micromachined Distrubuted Digital Phase Shifter for Microwave Phased Array Applications

Novel millimeter wave power-combining system in 3-D packaging level

Wafer Level Micropackaging for RF MEMS Switches

Research status of wafer level packaging for RF MEMS switches

A Bulk Micromachined Distributed Digital Microwave Phase Shifter with Butterfly Multilayer Bridges and MAM Capacitors

Wafer-Level Packaging Method For Rf Mems Applications Using Pre-Patterned Bcb Polymer

Parasitic Effects Reduction for Wafer-Level Packaging of RF-Mems

Design and Implementation of RF Front-End Module Based on 3D Heterogenous-Integrated Wafer-Level Packaging

Wideband Compartment Shielding Technique for Miniaturized Packages Based on Electrically Small Single-Negative Meta-Diaphragm

Notice of Violation of IEEE Publication PrinciplesKa-band Distributed MEMS Phase Shifters on Silicon Using AlSi Suspended Membrane

Packaging a RF-MEMS system

Design and analysis of a bulk micromachined distributed digital microwave phase shifter on glass substrate

Enhanced Thermal Conductivity and Microwave Dielectric Properties by Mesostructural Design of Multiphase Nanocomposite

Ultrathin, Electrically Small Noise Suppression Sheet for Microwave Cavities of 3-D Integrated Circuits: Design Methodology and Realization