Abstract:Elasto-plastic numerical analyses have been carried out for bonded dissimilar materials with different hardening properties, by using the boundary element method (BEM) and the finite element method (FEM). From the stress distribution near the interface edge, the elasto-plastic singular behavior has been investigated. It is found that there will be a meaningful region within which the elasto-plastic singular stress field becomes dominant under the large scale yielding condition. Therefore the fracture shall be evaluated by the elasto-plastic interfacial mechanics for such a case. The singularities determined numerically agree well with the theoretical results. It is also found that both the size of the yield zone and the stress distribution near the edge are dependent of the material combination. However, in the side of the material with smaller hardening exponent (the “harder” side), the theoretical singular stress field is not valid. Moreover, if the difference between two hardening exponents of the composed materials is very small, the displacement-matching method is no longer applicable. It is also found that the properties of the material with smaller hardening exponent mainly influence the angular stress distribution around the interface edge, but have very few effects on the singular stress order. It is also verified that the theoretical elastic solution of the singular stress field remains useful under the small scale yielding condition. Introduction Structures composed of bonded dissimilar materials have a wide application in engineering. To evaluate their strengths or reliabilities, the linear interfacial mechanics has been developed in the last decade [1]. However, for the cases such as ceramic/metal joints in which the yield strength of one composed material is relatively low, the elasto-plastic stress singular behavior [2-4] near the interface edge may have a strong effect on the strength. The evaluation approach based on the elasto-plastic interfacial mechanics is necessary. The authors [5] have theoretically deduced the elasto-plastic singular stress field near the interface edge of bonded linear hardening materials. It is found that the elasto-plastic stress singular behavior depends on not only the hardening coefficients, but also on the elastic properties. The elasto-plastic singular stress in this case can be determined by the two generalized Dundurs’ parameter and the geometry of the interface edge. The authors [6] have also proposed a method to determine the elasto-plastic stress singular order and the distribution near the interface edge of bonded dissimilar power-law hardening materials, based on the displacementmatching method [7,8] and two path-independent integrals. It is found that when the interface edge is degenerated to an interface crack, the results obtained by this method agree with that for an interface crack [7,8]. In this study, the elasto-plastic boundary element method (BEM) and finite element method (FEM) analyses have been carried out to investigate the elasto-plastic singular behaviors of bonded linear and power-law hardening materials, respectively. Based on the comparison of the numerical and the theoretical results, the validity and the applicable range of the theoretical solutions have been clarified. Interface edge of Bonded Linear Hardening Materials Theoretical Results Introducing the generalized Dundurs’ parameters as [5]

Interface debonding ahead of a primary crack

Interface debonding by growth of interface defect ahead of main crack approaching with oblique paths in layered systems

Fundamental Solutions of a Crack Impinging Upon an Interface Slippage in Laminated Anisotropic Bodies

On the Interface Debonding Models

Interfacial fracture criteria based on the nominal deformation energy of interface

Finite size effects on crack front pinning at heterogeneous planar interfaces: Experimental, finite elements and perturbation approaches

Perturbation analysis of Mode III interfacial cracks advancing in a dilute heterogeneous material

A Novel Strength-Energy Criterion for Bimaterial Interface Crack Propagation

Interface Between an Old Concrete and a Bonded Overlay: Debonding Mechanism

Mechanics of dynamic debonding

Nonlinear Fracture Analysis of Delamination Crack Jumps in Laminated Composites

Debonding mechanisms in the presence of an interphase in composites

Finite deformation near a crack tip terminated at an interface between two neo-Hookean sheets

Crack Deflection at an Interface Between Dissimilar Piezoelectric Materials

Stress based criterion for an interface crack kinking out of the interface in dissimilar materials

Interaction of an interfacial crack with linear micro-defects under out-of-plane shear loading

Application of a linear elastic - brittle interface model to the crack initiation and propagation at fibre-matrix interface under biaxial transverse loads

Interaction Between an Interface and Cracks

Elastoplastic singular stress field for a crack meeting an interface between two linear hardening bonded materials

Elasto-Plastic Singular Behavior at an Interface Edge

Mechanics and fracture of crack tip deformable bi-material interface