Abstract:During water electrolysis on 3D electrodes, gas bubbles can get trapped; this work evaluates 3D printed electrode geometries with triply periodic minimal surfaces (TPMS); a combined experimental and modeling approach identifies the TPMS structural parameters that minimize bubble entrapment; under forced electrolyte flow, the cell overpotential can be reduced by more than 20%. A zero‐gap cell with porous electrodes is a promising configuration for alkaline water electrolysis. However, gas evacuation becomes a challenge in that case, as bubbles can get trapped within the electrode's 3D structure. This work considers a number of 3D printed electrode geometries with so‐called triply periodic minimal surfaces (TPMS). The latter is a mathematically defined structure that repeats itself in three dimensions with zero mean curvature, and can therefore be expected to be particularly well‐suited to enhance gas evacuation. Another advantage as compared to other state‐of‐the‐art 3D electrodes like foams or felts lies in the fact that their porosity, which determines the available surface area, and their pore size or flow channel dimensions, which determines the degree of bubble entrapment, can be varied independently. By a combined experimental and modeling approach, this work then identifies the structural parameters that direct the performance of such 3D printed TPMS geometries toward enhanced gas evacuation. It is demonstrated that an optimal combination of these parameters allows, under a forced electrolyte flow, for a reduction in cell overpotential of more than 20%. This indicates that efforts in optimizing the electrode's geometry can give a similar electrochemical performance enhancement as optimizing its electro‐catalytic composition.

Water Splitting: Periodic Porous 3D Electrodes Mitigate Gas Bubble Traffic during Alkaline Water Electrolysis at High Current Densities (Adv. Energy Mater. 46/2020)

Periodic Porous 3D Electrodes Mitigate Gas Bubble Traffic during Alkaline Water Electrolysis at High Current Densities

Manageable Bubble Release Through 3D Printed Microcapillary for Highly Efficient Overall Water Splitting

Bubbles in Porous Electrodes for Alkaline Water Electrolysis

Electrochemical Performance Enhancement of 3D Printed Electrodes Tailored for Enhanced Gas Evacuation during Alkaline Water Electrolysis

In-situ Investigation and Modeling of Electrochemical Reactions with Simultaneous Oxygen and Hydrogen Microbubble Evolutions in Water Electrolysis

Ni Electrodes with 3D-Ordered Surface Structures for Boosting Bubble Releasing Toward High Current Density Alkaline Water Splitting

High‐Rate Alkaline Water Electrolysis at Industrially Relevant Conditions Enabled by Superaerophobic Electrode Assembly

Novel Water-Splitting Electrolyzer Design Incorporating a Gas Diffusion Electrode and a Gel Membrane for Highly Efficient Hydrogen Production

A Multi‐Bioinspired Dual‐Gradient Electrode for Microbubble Manipulation toward Controllable Water Splitting

Bubble Growth and Departure Modes on Wettable/non-Wettable Porous Foams in Alkaline Water Splitting

Proton exchange membrane-like alkaline water electrolysis using flow-engineered three-dimensional electrodes

Antibuoyancy and Unidirectional Gas Evolution by Janus Electrodes with Asymmetric Wettability.

Integrated Catalyst-Substrate Electrodes for Electrochemical Water Splitting: A Review on Dimensional Engineering Strategy

Design and Synthesis of Hollow Nanostructures for Electrochemical Water Splitting

"Bubble-Diode" Breathable Electrodes for Fast Gas Transport

Water Splitting by Electrolysis at High Current Densities under 1.6 Volts

Hybrid Heterostructure Ni3N|NiFeP/FF Self‐Supporting Electrode for High‐Current‐Density Alkaline Water Electrolysis

Improving the Efficiencies of Water Splitting and CO2 Electrolysis by Anodic O2 Bubble Management.

Stereolithgraphy of Metallic Electrode with Janus Porosity toward Controllable Bubble Behavior and Ultra‐Stable Water Electrolysis

Recent Advances in Design of Electrocatalysts for High-Current-Density Water Splitting