Abstract:It is suggested that fatigue failure mechanisms in the face-centered cubic metals are greatly affected by stacking fault energy. It was from this viewpoint that the fatigue crack initiation and stage I type crack propagation in 18-8 austenitic steel which had the lowest stacking fault energy among the face-centered cubic metals on the market, were discussed by the X-ray microbeam diffraction technique and the replica electron microscopic method.The fatigue slip line at room temperature tests has fine and straight configurations which are characteristic of low stacking fault energy materials, while the wavy and coarse slip line is typical of fatigue tests at 200°C where screw dislocation is more easily prone to cross slip. In both of these cases very complicated deformation configurations are caused by double slip and cross slip near the grain boundaries, and frequent extrusion and intrusion are observed in these areas. Fatigue crack nucleation might be caused by stress concentration at the notch and peak topography. The stage I type fatigue crack propagates immediately after the initiation, mainly along and frequently across the intense slip lines. Its growth in the area neighbouring the grain boundary runs in the direction that depends on both the crystal orientations of the grain containing the crack and the grains adjacent to it.Total misorientation and micro lattice strain measured by X-ray micro-beam diffraction technique increase abruptly at early fatigue stressing, then equilibrium values are attained and finally increase rapidly. These three periods during the fatigue deformation might be corresponding to those of the fine slip line initiation, the intensification of each slip line without new slip line formation and of final initiation of micro crack, respectively. Furthermore it will be noticed that the equilibrium value of total misorientation of 18-8 austenitic steel during the fatigue process is about one-tenth of that of carbon steel.The area of substructural zone near the fatigue crack of 18-8 austenitic steel is smaller than that of aluminum of high stacking fault energy and body-centered cubic iron. Therefore, the formations of subgrain and martensite could not be detected by X-ray micro-beam diffraction technique when irradiated by Cr-Kα of 200μφ beam size. In order to clarify these points the detailed observation at the fatigue crack tip must be made by using transmission electron microscopy. These results will be reported elsewhere.

Failure analysis of an AISI 310 stainless steel beam reinforcement fracture during service in a rolling beam furnace

Estimation of Residual Stresses by Nanoindentation in an Experimental High Strength Microalloyed Steel Subjected to Rapid Thermal Cycles

The low-cycle fatigue, deformation and final fracture behaviour of an austenitic stainless steel

High cycle thermal fatigue of two austenitic stainless steels

MICRO-CRACK ANALYSIS IN THE STUDY OF FATIGUE FRACTURE IN THE HAZ IN THE HIGH YIELD STRENGTH MICRO-ALLOYED STEELS

Creep in welded AISI 310 steel – An experimental comparison between fracture and phase transformation

High-Cycle Fatigue Fracture Behavior of Ultrahigh Strength Steels

Microscopic Observations of Fatigue Crack Initiation Process in 18-8 Austenitic Steel

Cracking of AISI 309S Stainless Steel Lance Tube Used for Coal Injection in Blast Furnace

Effect of Solution Annealing on Fatigue Crack Propagation in the AISI 304L TRIP Steel

Failure investigation of an AISI 316L pipe of the flare system in an off-shore oil platform

Micro-mechanics investigation of heterogeneous deformation fields and crack initiation driven by the local stored energy density in austenitic stainless steel welded joints

Fracture Analysis on A Cylindrical Shell Section of the Low-Pressure Absorption Tower

An In Situ Study of Short Crack Initiation and Propagation During Fatigue Testing of a Hot Isostatically Pressed Al-7%Si-0.5%Mg (A357-T6) Alloy Specimen

In-situ SEM study on fatigue crack behavior of a nickel-based single crystal alloy at 950 °C and 1050 °C

The Effects of Microstructure and Microtexture Generated During Solidification on Deformation Micromechanism in IN713C Nickel-Based Superalloy

Research on the Mechanism of Oxygen-Induced Embrittlement Fracturing in Industrial Electrolytic Nickel

Failure Analysis of 304 Stainless Steel Tube in Fire Furnace

Analysis of Edge Crack Defect Analysis and Control of 316L Austenitic Stainless Steel

Quantitative Assessment of Microstructural Damage for Interior Crack Initiation and High Cycle Fatigue Life Modeling

Microstructural Dependence of Anisotropic Fracture Mechanisms in Cold-Drawn Pearlitic Steels