Abstract:The B 4 C-reinforced Ni–P composite coatings were synthesized on low-carbon steel via ultrasonic-assisted electrodeposition. The optimal condition for producing co-electrodeposited Ni–P coating is to investigate the effects of concentrations of B 4 C on the morphology, microstructure, surface roughness, hardness, elastic modulus, friction, wear, and electrochemical properties of the composite coating. Field-emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), and energy dispersive spectrometer (EDS) were used to analyze the surface microstructure, crystallite size, morphology and composition of coating and content and distribution of the particles. The nanohardness and reduced elastic modulus of B 4 C-reinforced Ni–P depositions was characterized by the nanoindentation technique. The friction and wear mechanism of the composite coatings was discussed in detail. The electrochemical properties of samples were studied via open circuit potential (OCP), potentiodynamic test and electrochemical impedance spectroscopy (EIS) in the 3.5% NaCl media. The experimental results indicated the highest elastic modulus and nano hardness (147 GPa and 6,92 GPa and the lowest wear rate (3.18 X 10 –8 mm 3 /Nm) and average coefficient of friction (0,35) for coatings deposited at 20 gL −1 . Moreover, the corrosion resistance is significantly improved; this is shown via the low corrosion current density (I corr value of 1.48 × 10 –3 A/cm 2 ), the high corrosion potential (E corr value of – 0.56 V), best corrosion rate (1.36 X10 −5 mpy) and maximum R ct of 181.8 kΩ cm 2 . These results are attributed to the uniform distribution of the B 4 C into nickel coating and the grain refinement effect of electrodeposited Ni–P coating. The formation of the B 4 C core–shell structure on the coating surface improved the interfacial bond between the matrix and the ceramic particle, improving wear resistance and anti-corrosion performance.

STUDY OF THE STRUCTURE AND PHASE COMPOSITION OF Ni+B4C COMPOSITE COATINGS PRODUCED BY COLD SPRAYING

Study of corrosion resistance of cold sprayed Al + B4C composite coatings

Study on morphology, wear and corrosion resistance of ultrasonic-assisted pulse co-electrodeposited B4C reinforced Ni–P composite coating

Multiple strengthening mechanisms of cold-sprayed cBNp/NiCrAl composite coating

Thermal Stability of Microstructure and Hardness of Cold-Sprayed cBNp/NiCrAl Nanocomposite Coating

Investigation of the Al-Mo-B(CN) Coatings Deposited Using Magnetron Sputtering of Al-Mo-B4C Target Produced by Detonation Spray Coating

Microstructure, Mechanical Properties, and Two-Body Abrasive Wear Behavior of Cold-Sprayed 20 vol.% Cubic BN-NiCrAl Nanocomposite Coating

Thermal Stability of Microstructure and Hardness of Cold-Sprayed cBN/NiCrAl Nanocomposite Coating

Effect of Annealing on Microstructure of Cold Sprayed C-BNp/NiCrAl Composite Coating

Microstructure and properties of CrB2-Cr3C2 composite coatings prepared by plasma spraying

Microstructure and Mechanical Properties of In-Situ TiB2 Particle Reinforced AlSi10Mg Composite Coatings Produced by Cold Spraying

The Microstructure, Surface Topography and Wear Resistance of Cold-Sprayed (Cr3C2-25(Ni20Cr))-(Ni-graphite) Composite Coatings Modified by Diode Laser Treatment

Study on the performance of laser nitriding in situ enhanced Co12/TC4 composite Ag self-lubricating coating on TC4 surface

Fabrication of cBN-NiCrAl Cermet Coating by Cold Spray

Study on Microstructure and Properties of FeNiCr/Ni Coated Cr_3C_2 Coatings Deposited by High Velocity Arc Spraying

INFLUENCE OF THE STRUCTURE OF IRON-TITANIUM THERMAL SPRAYED COATINGS ON THEIR WEAR RESISTANCE

Evaluation of the Wear Properties and Corrosion Resistance of 52100 Steel Coated with Ni/CrC by Cold Spraying

Microstructures and Mechanical Properties of (Ti,Cr)N Composite Coatings Grown by Arc Ion Plating

Preparation of Ni-based Alloy Diamond Composite Coatings by Cold Spray

Microstructure and properties of laser cladding in-situ ceramic particles reinforced Ni-based coatings

Influence of Annealing on the Microstructure and Wear Performance of Diamond/NiCrAl Composite Coating Deposited Through Cold Spraying