Abstract:Introduction: Bone defects remain a thorny challenge that clinicians have to face. At present, scaffolds prepared by 3D printing are increasingly used in the field of bone tissue repair. Polylactic acid (PLA) has good thermoplasticity, processability, biocompatibility, and biodegradability, but the PLA is brittle and has poor osteogenic performance. Beta-tricalcium phosphate (Î2-TCP) has good mechanical properties and osteogenic induction properties, which can make up for the drawbacks of PLA. Methods: In this study, photocurable biodegradable polylactic acid (bio-PLA) was utilized as the raw material to prepare PLA/Î2-TCP slurries with varying Î2-TCP contents (Î2-TCP dosage at 0%, 10%, 20%, 30%, 35% of the PLA dosage, respectively). The PLA/Î2-TCP scaffolds were fabricated using liquid crystal display (LCD) light-curing 3D printing technology. The characterization of the scaffolds was assessed, and the biological activity of the scaffold with the optimal compressive strength was evaluated. The biocompatibility of the scaffold was assessed through CCK-8 assays, hemocompatibility assay and live-dead staining experiments. The osteogenic differentiation capacity of the scaffold on MC3T3-E1 cells was evaluated through alizarin red staining, alkaline phosphatase (ALP) detection, immunofluorescence experiments, and RT-qPCR assays. Results: The prepared scaffold possesses a three-dimensional network structure, and with an increase in the quantity of Î2-TCP, more Î2-TCP particles adhere to the scaffold surface. The compressive strength of PLA/Î2-TCP scaffolds exhibits a trend of initial increase followed by decrease with an increasing amount of Î2-TCP, reaching a maximum value of 52.1Â MPa at a 10% Î2-TCP content. Degradation rate curve results indicate that with the passage of time, the degradation rate of the scaffold gradually increases, and the pH of the scaffold during degradation shows an alkaline tendency. Additionally, Live/dead staining and blood compatibility experiments suggest that the prepared PLA/Î2-TCP scaffold demonstrates excellent biocompatibility. CCK-8 experiments indicate that the PLA/Î2-TCP group promotes cell proliferation, and the prepared PLA/Î2-TCP scaffold exhibits a significant ability to enhance the osteogenic differentiation of MC3T3-E1 cells in vitro . Discussion: 3D printed LCD photocuring PLA/Î2-TCP scaffolds could improve surface bioactivity and lead to better osteogenesis, which may provide a unique strategy for developing bioactive implants in orthopedic applications.

DLP printing of BT/HA nanocomposite ceramic scaffolds using low refractive index BT crystals

Digital light processing (DLP) of nano biphasic calcium phosphate bioceramic for making bone tissue engineering scaffolds

Digital light processing 3D printing of barium titanate/1,6-ethylene glycol diacrylate/polyethylene glycol (400) diacrylate nanocomposites

3D printing of hydroxyapatite scaffolds with good mechanical and biocompatible properties by digital light processing

3D printed barium titanate/calcium silicate composite biological scaffold combined with structural and material properties

Preparation of BMP-2/PDA-BCP Bioceramic Scaffold by DLP 3D Printing and its Ability for Inducing Continuous Bone Formation

DLP 3D printing porous β-tricalcium phosphate scaffold by the use of acrylate/ceramic composite slurry

Ln Vitro Assessment of Immunomodulatory and Osteogenic Properties in 3D-Printed Hydroxyapatite/barium Titanate Piezoelectric Ceramic Scaffolds

Preparation and properties of K0.48Na0.52NbO3 ceramics for bone scaffolds via digital light processing

Fabrication of biphasic scaffold composed of bioceramic‐loaded and water‐based photosensitive resins through vat photopolymerization

Aligned porous barium titanate/hydroxyapatite composites with high piezoelectric coefficients for bone tissue engineering

Fabrication and properties of PLA/Î2-TCP scaffolds using liquid crystal display (LCD) photocuring 3D printing for bone tissue engineering

High performance hydroxyapatite ceramics and a triply periodic minimum surface structure fabricated by digital light processing 3D printing

3D/4D printed bio-piezoelectric smart scaffolds for next-generation bone tissue engineering

3D-Printed Piezoelectric Scaffolds with Shape Memory Polymer for Bone Regeneration

369Fabrication of 3D gel-printed β-tricalcium phosphate/titanium dioxide porous scaffolds for cancellous bone tissue engineering

Microstructures and mechanical properties of biphasic calcium phosphate bioceramics fabricated by SLA 3D printing

Synthesis, Characterization and Bioactivity Evaluation of Porous Barium Titanate with Nanostructured Hydroxyapatite Coating for Biomedical Application

Zirconia toughened hydroxyapatite biocomposite formed by a DLP 3D printing process for potential bone tissue engineering

Performance of 3D printed porous polyetheretherketone composite scaffolds combined with nano-hydroxyapatite/carbon fiber in bone tissue engineering: a biological evaluation

A brief study of electrical and biological properties of BNT6BT/ZnO-HA Composite