Abstract:As a surface peening technique, shot peening introduces residual compressive stresses to the surface of the part, which effectively increases the fatigue life of the structure and material. However, when structures are subjected to alternating loads, this can lead to stress relaxation on the material surface, weakening the effectiveness of the shot peening process. In addition, reasonable shot peening parameters are essential. In this paper, the effects of shot peening pressure and shot coverage on the fatigue life of materials during shot peening were investigated, followed by fatigue tests on 20CrMnTi specimens using a high-frequency fatigue testing machine to study the effects of shot peening and re-shot peening on the fatigue life of shot-peened materials after different load cycles. The results show that a reasonable shot peening pressure and coverage rate can significantly improve the fatigue life of the material, while a shot peening pressure higher than 0.4 MPa will reduce the fatigue life of the material 20CrMnTi. Coverage rates of 100% and 200% can both improve the fatigue life of the material, while a 200% coverage rate has a better strengthening effect. Re-shot peening removes the residual compressive stress relaxation on the surface of the material caused by cyclic loading and improves the fatigue life of the material. The maximum value of the residual compressive stress on the surface of the test material after shot peening is 443 MPa, and after a certain number of fatigue loads, the residual compressive stress on the surface is reduced to 203 MPa, which is subjected to secondary shot peening, and the residual compressive stress is restored to 415 MPa, and the fatigue life is significantly increased. When the second shot peening time is taken as 25% of the fatigue life of the initial shot blasting of the material, the shot peening effect is better.

A new thermal vibration mechanical shot peening coupling strengthening method

Effects of Ultrasonic Shot Peening on Fatigue Behavior of TA15 Titanium Alloy Fabricated by Laser Melting Deposition

Microstructures and rolling contact fatigue behaviors of 17Cr2Ni2MoVNb steel under combined ultrasonic surface rolling and shot peening

Investigation of Wet Shot Peening on Microstructural Evolution and Tensile-Tensile Fatigue Properties of Ti-6Al-4V Alloy

Comparative study of the effects of conventional shot peening and ultrasonic shot peening on very high cycle fatigue properties of GH4169 superalloy

Effect of Surface Roughness and Compressive Residual Stress on the Fatigue Performance of TC4 Titanium Alloy Subjected to Laser Shock Wave Planishing

Surface mechanical property and residual stress stability of nanostructured CNT/Al-Cu-Mg composites induced by shot peening

Understanding the Relations between Surface Stress State and Microstructure Feature for Enhancing the Fatigue Performance of TC6 Titanium Alloy

In-situ warm shot peening on Ti-6Al-4V alloy: Effects of temperature on fatigue life, residual stress, microstructure and mechanical properties

Improving the high-cycle fatigue life of a high-strength spring steel for automobiles by suitable shot peening and heat treatment

Effect of Surface Strengthening by Ultrasonic Shot Peening on TC17 Alloy

Anti-fatigue strengthening mechanism of conventional shot peening and micro-shot peening on bare and micro-arc oxidation coated 6082-T6 aluminum alloy

The Fatigue Deformation Mechanism of TC17 Alloy with Residual Stress and Microstructure Dual Gradients

Microstructure Evolution, Hardness, and Tribological Behaviors of Ti-50.8Ni SMA Alloy with Ultrasonic Surface Shot Peening Treatment

Comparative assessment of Ti‐6Al‐4 V titanium alloy fatigue life improvement by vibratory peening, shot peening, and vibratory finishing

Microstructure Evolution and Numerical Modeling of TC4 Titanium Alloy during Ultrasonic Shot Peening Process

Mechanism for magnetic field induced structural relaxation and accompanying fracture toughness improvement of the thermal spraying coating

Effects of shot peening on microstructure evolution and mechanical properties of surface nanocrystal layer on titanium matrix composite

Gradient microstructure and foreign-object-damaged fatigue properties of Ti6Al4V titanium alloy processed by the laser shock peening and subsequent shot peening

An experimental study of residual stress induced by ultrasonic shot peening

Experimental Study on the Effect of Shot Peening and Re-Shot Peening on the Residual Stress Distribution and Fatigue Life of 20CrMnTi