Abstract:The use of secondary batteries has been on the rise in recent years, especially solid-state batteries. However, security issues have become a major challenge in practical applications. Both lithium-ion batteries and lithium–sulfur batteries have safety problems that need to be solved. Herein, a polymer electrolyte suitable for the two types of batteries was easily synthesized. A polyvinylidene fluoride (PVDF)-based polymer electrolyte with 1-butyl-1-methyl pyrrolidine bis-trifluoromethyl sulfonimide (Py14TFSI) was used as the solid electrolyte. The ionic conductivity of the LiTFSI/Py14TFSI/cellulose acetate (CA)/PVDF polymer electrolyte was 1.45 × 10–4 S cm–1. The electrochemical stability window was 4.95 V. The transference number of the lithium ion was 0.231. The constant-current polarization test results showed that the polarization voltage was only 0.04 V when the current density was 1 mA cm–2. The first discharge specific capacity of the Li | LiTFSI/Py14TFSI/CA/PVDF | LiFePO4 battery was 125.7 mA h g–1 (0.5 C), and the capacity retention rate was 95.22% after 50 cycles at room temperature. A multistage porous conductive carbon (M-PCC) material with micropores and mesopores was applied as the host of the sulfur cathode of lithium–sulfur batteries. The M-PCC material provided a carrier for sulfur and sulfide with a specific surface area of 1132.68 m2 g–1. The solid-state lithium–sulfur battery (Li | LiTFSI/Py14TFSI/CA/PVDF | ) had excellent electrochemical performance. The first discharge specific capacity was 1245.9 mA h g–1 with an average Coulombic efficiency of 97.34%. The energy of Py14TFSI cation and Li2S8 calculated by DFT was 8.8345 eV, which indicated that the polysulfide cannot adsorb onto the polymer electrolyte. XPS was used to measure the elemental composition of the anode–electrolyte interface after charge–discharge cycling. The uniform growth of lithium dendrite was observed by the SEM image of the anode after cycles. The results showed that a solid-state lithium–sulfur battery produced uniform solid electrolyte interface films and completely suppressed the shuttle effect.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsaem.1c00658?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsaem.1c00658</a>.Experimental section; characterization; AFM of polymer electrolyte: PVDF/Py14TFSI = 10:0 and PVDF/Py14TFSI = 10:7.5; XRD patterns of M-PCC; SEM images of M-PCC and ; TEM images of M-PCC (40,000×) and M-PCC(200,000×); CV curves of the Li | liquid electrolyte/PP separator | battery; active products at different charge and discharge stages; impedance spectrum at different cycles of the Li | liquid electrolyte/PP separator | battery; TG curve of ; and comparison the discharge specific capacity of the Li | LiTFSI/Py14TFSI/CA/PVDF | battery with the previously reported solid polymer electrolyte lithium–sulfur batteries at different temperatures and rate capabilities (<a class="ext-link" href="/doi/suppl/10.1021/acsaem.1c00658/suppl_file/ae1c00658_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Facile and Powerful In Situ Polymerization Strategy for Sulfur-Based All-Solid Polymer Electrolytes in Lithium Batteries

In Situ Fabrication of Solvent-Free Solid Polymer Electrolytes for Wide-Temperature All-Solid-State Lithium Metal Batteries

Polymer-based electrolytes for all-solid-state lithium–sulfur batteries: from fundamental research to performance improvement

In Situ Constructing Ultrathin, Robust‐Flexible Polymeric Electrolytes with Rapid Interfacial Ion Transport in Lithium Metal Batteries

Facile Fabrication of Polymer Electrolytes via Lithium Salt-Accelerated Thiol-Michael Addition for Lithium-Ion Batteries

In Situ Polymerization Bi‐Functional Gel Polymer Electrolyte for High Performance Quasi‐Solid‐State Lithium−Sulfur Batteries

Cathode-Supported-Electrolyte Configuration for High-Performance All-Solid-State Lithium–Sulfur Batteries

In-Situ Synthesized Gel Polymer Electrolyte Enable High Capacity and Long-Cycle-Life Lithium Metal Batteries

Rationally Designed in-Situ Gelled Polymer-Ceramic Hybrid Electrolyte Enables Superior Performance and Stability in Quasi-Solid-State Lithium-Sulfur Batteries

Ultrathin polymer electrolyte film prepared by in situ polymerization for lithium metal batteries

Interfacial Chemistry and Ion Transfer Mechanism for Tailored Poly(thioether) Enabled Hybrid Solid Polymer Electrolyte with Electrochemical Properties in All-Solid-State Lithium-Sulfur Batteries

Key issues and modification strategies towards high-performance polymer all-solid-state lithium-sulfur batteries

Research Progresses of in Situ Polymerized Electrolytes for Solid-state Lithium Metal Batteries

Rational design of a topological polymeric solid electrolyte for high-performance all-solid-state alkali metal batteries

In situ initiator-free gelation of highly concentrated lithium bis(fluorosulfonyl)imide-1,3-dioxolane solid polymer electrolyte for high performance lithium-metal batteries

Ternary Stabilization Strategies for Succinonitrile-Based in Situ Polymerized Electrolyte Enabling High-Performance Solid Lithium Metal Batteries

Engineering Molecule‐Designed In Situ Polymerization on Al‐Doped Molecular‐Sieve Framework Enables Robust Quasi‐Solid‐State Lithium Batteries

Progress and Perspectives of in Situ Polymerization Method for Lithium‐based Batteries

Solid-State Polymer Electrolyte Solves the Transfer of Lithium Ions between the Solid–Solid Interface of the Electrode and the Electrolyte in Lithium–Sulfur and Lithium-Ion Batteries

Lithium Salt Catalyzed Ring-Opening Polymerized Solid-State Electrolyte with Comparable Ionic Conductivity and Better Interface Compatibility for Li-Ion Batteries

High Polymerization Conversion and Stable High-Voltage Chemistry Underpinning an In Situ Formed Solid Electrolyte