Abstract:Equal channel angular pressing (ECAP) is an efficient metal forming tool, generally used to improve the mechanical properties by refining the grain structure in metals and alloys. In the present work, both experimental and simulation approaches have been utilized to investigate the deformation behavior of EN AW 7075 alloy during ECAP. The formation and homogeneity of the Von-Mises stress and plastic strain of the samples during ECAP with different outer corner angles (OCAs) have been investigated by the finite element method (FEM). The results revealed that the effective strain was higher and uniform for 10°, 20°, and 30° OCAs die compared to other OCAs. Beyond 30°, the magnitude of strain was found lower with a less homogenous distribution of strain. A sharp plastic deformation zone (PDZ) was noticed for 10° and 20° OCAs, although broadened gradually over an OCA value of 20°. Moreover, lower and uniform Von-Mises stress was generated along the diameter of the sample for the OCA of 20° compared to other OCAs. A gradual reduction of plastic strain has been documented with the enhancement of OCAs along with the sample diameter. The sharpest damage, however, was noticed for the OCA of 90° due to the higher gap between the sample and both die surfaces. Interestingly, the most uniform severe plastic deformation and highest strain homogeneity in terms of inhomogeneity index and coefficient of variance were achieved for 20° and 30° OCAs. Electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM) analysis illustrated the formation of ultra-fine grain structures containing very fine η ́ and η precipitates during the post-ECAP process. An improvement in the hardness, yield strength, and ultimate strength by 22%, 18%, and 14%, respectively, after ECAP has been recorded in comparison to the initial artificially aged condition. The improvements in mechanical properties were improvised primarily due to grain refinement combined with precipitate hardening.

Optimization of Process Parameters of Cyclic Expansion Extrusion Process for Effective Grain Refinement of Al-Mg-Si Alloy

Effect of the cyclic expansion-extrusion (CEE) process on mechanical properties and the grain refinement of AA6061 aluminum alloy

The improvement of grain refinement, texture modification and mechanical properties of pure Mg prepared by cyclic expansion extrusion with an asymmetric extrusion cavity

Optimization of numerical parameters and microstructure evolution on 2195 Al–Li alloy extrusion process

Design and analysis of ECAP Processing for Al6061 Alloy: a microstructure and mechanical property study

Influence of Equal Channel Angular Extrusion on the Properties of Mg-6Al Alloy

Preparing Mg-6Al alloy with high mechanical properties and fine grains by equal channel angular extrusion

Microstructure and mechanical properties of AZ31 alloy prepared by cyclic expansion extrusion with asymmetrical extrusion cavity

Grain Refinement of Magnesium Alloys Processed by Severe Plastic Deformation

Optimization of Deformation Behaviors during Continuous Forming Extrusion of C18150 Copper Alloy through Response Surface Methodology

Effects of optimizing continuous forging extrusion process on the microstructure and mechanical properties of AZ31 magnesium alloy

Microstructure Evolution of AZ Series Magnesium Alloys During Cyclic Extrusion Compression

Optimization of ECAP parameters of ZX30 alloy using feature engineering assisted machine learning and response surface approaches

Cyclic Extrusion Compression Process for Achieving Ultrafine-Grained 5052 Aluminum Alloy with Eminent Strength and Wear Resistance

Microstructure Evolution and Mechanical Properties of an Az61 Mg Alloy Through Cyclic Extrusion Compression

Investigating the Influence of Thermomechanical Equal Channel Angular Pressing (ECAP) Improved Die on AA-6061

Microstructure, Phase Transformation and Wear Behavior of Cu–10%Al–4%Fe Alloy Processed by ECAE

A novel continues multi-shear extrusion process on the microstructure and mechanical property evolution of AZ31 magnesium alloys

Effects of Cyclic Extrusion and Compression Parameters on Microstructure and Mechanical Properties of Mg–1.50Zn–0.25Gd Alloy

Development of mechanical properties and microstructure for Al–Zn–Mg–Cu alloys through ECAP after optimizing the outer corner angles through FE modeling

Effect of ECAE Conditions on the Microstructure, Texture and Mechanical Properties of an Extruded Mg–Zn–Y–Zr Alloy