Abstract:Previous studies have demonstrated volatility-dependent absorption of gas-phase volatile organic compounds (VOCs) to Teflon and other polymers. Polymer–VOC interactions are relevant for atmospheric chemistry sampling, as gas–wall partitioning in polymer tubing can cause delays and biases during measurements. They are also relevant to the study of indoor chemistry, where polymer-based materials are abundant (e.g., carpets and paints). In this work, we quantify the absorptive capacities of multiple tubing materials, including four nonconductive polymers (important for gas sampling and indoor air quality), four electrically conductive polymers and two commercial steel coatings (for gas and particle sampling). We compare their performance to previously characterized materials. To quantify the absorptive capacities, we expose the tubing to a series of ketones in the volatility range 10 4 – 10 9 μg m −3 and monitor transmission. For slow-diffusion polymers (e.g., perfluoroalkoxy alkane (PFA) Teflon and nylon), absorption is limited to a thin surface layer, and a single-layer absorption model can fit the data well. For fast-diffusion polymers (e.g., polyethylene and conductive silicone), a larger depth of the polymer is available for diffusion, and a multilayer absorption model is needed. The multilayer model allows fitting solid-phase diffusion coefficients for different materials, which range from 4×10-9 to 4×10-7 cm 2 s −1 . These diffusion coefficients are ∼ 8 orders of magnitude larger than literature values for fluorinated ethylene propylene (FEP) Teflon film. This enormous difference explains the differences in VOC absorption measured here. We fit an equivalent absorptive mass ( C W , μg m −3 ) for each absorptive material. We found PFA to be the least absorptive, with C W ∼ 10 5 μg m −3 , and conductive silicone to be the most absorptive, with C W ∼ 10 13 μg m −3 . PFA transmits VOCs easily and intermediate-volatility species (IVOCs) with quantifiable delays. In contrast, conductive silicone tubing transmits only the most volatile VOCs, denuding all lower-volatility species. Semi-volatile species (SVOCs) are very difficult to sample quantitatively through any tubing material. We demonstrate a system combining several slow- and fast-diffusion tubing materials that can be used to separate a mixture of VOCs into volatility classes. New conductive silicone tubing contaminated the gas stream with siloxanes, but this effect was reduced 10 000-fold for aged tubing, while maintaining the same absorptive properties. SilcoNert (tested in this work) and Silonite (tested in previous work) steel coatings showed gas transmission that was almost as good as PFA, but since they undergo adsorption, their delay times may be humidity- and concentration-dependent.

Reduction in the transport of sour gases and hydrocarbons to underlying PE-RT through thin films of PVDF

Molecular Simulation on Permeation Behavior of CH4/CO2/H2S Mixture Gas in PVDF at Service Conditions

Preparation of High Density Polyethylene/polyethylene- Block -Poly(ethylene Glycol) Copolymer Blend Porous Membranes Via Thermally Induced Phase Separation Process and Their Properties

Diffusion measurements of isopentane, hexene, cyclohexane in polyethylene particles

Permeation Characteristics of CH4 in PVDF with Crude Oil-Containing

Investigation of the Gas Permeation Properties Using the Volumetric Analysis Technique for Polyethylene Materials Enriched with Pure Gases under High Pressure: H2, He, N2, O2 and Ar

Qualification of a New Robust and Cost-Effective Polymer for Flexible Pipe Pressure Sheath

Permeance of Condensable Gases in Rubbery Polymer Membranes at High Pressure

Molecular Simulation Study on the Hydrogen Permeation Behavior and Mechanism of Common Polymers

Critical Assessment of PVDF Multilayer Barriers in Unbonded Flexible Risers: Applications and Benefits

Assessment of the Integrity of the PVDF Barrier in Unbonded Flexible Pipes

Unveiling the Role of PTFE Surface Coverage on Controlling Gas Diffusion Layer Water Content

Diffusion and partitioning of different PFAS compounds through thermoplastic polyurethane and three different PVC-EIA liners

Compatibility study of high density polyethylene grade 80 gas pipe with synthetic polyglycol-based brake oil

Increasing the Permeability of Carbon Dioxide and Nitrogen Gases Through a Polymer Membrane Consisting of a Modified Polyether Block Amide and Experimental Design

Engineered pinhole-stitching process of PEI-based hollow fiber membrane enables preferred performance toward light gas separation

High performance polymers for membrane separation

Dissipative Particle Dynamics Study and Experimental Verification on the Pore Morphologies and Diffusivity of the Poly (4-Methyl-1-pentene)-diluent System Via Thermally Induced Phase Separation: the Effect of Diluent and Polymer Concentration

Correlations between H2 Permeation and Physical/Mechanical Properties in Ethylene Propylene Diene Monomer Polymers Blended with Carbon Black and Silica Fillers

The relationship between chemical microstructure, crystallinity, mechanical properties, and CO2/N2 gases permselectivity of thermoplastic polyurethane membranes

Absorption of volatile organic compounds (VOCs) by polymer tubing: implications for indoor air and use as a simple gas-phase volatility separation technique