Abstract:The large thermal gradient and high cooling rate generated in the fabrication of complex thin-walled components by laser powder bed fusion (LPBF) may cause uncontrolled deformation and reduce dimensional accuracy. The existing preheating-assisted LPBF process is still difficult to fabricate complex thin-walled components to large size (e.g., reach 800 mm) with the required dimensional accuracy and structural properties. To solve this problem, a novel integrated process of LPBF and hot metal gas forming (HMGF) was proposed in this study to fabricate complex thin-walled components. In this process, a preform with a geometrical shape close to the final component is first fabricated by LPBF process, and then this preform is formed into the desired shape by HMGF process. The hot formability of the LPBF AlSi10Mg sheets was investigated to verify the feasibility of this novel forming process. Also, the hot formability was compared with that of gravity cast (GC) AlSi10Mg sheets. The microstructure, phase structure, uniaxial and biaxial hot formability were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), hot uniaxial tensile and hot biaxial gas bulging experiments, respectively. The results indicated that the cellular microstructure of the LPBF AlSi10Mg gradually disappears with the increase in temperature. The LPBF AlSi10Mg sheet exhibits superior mechanical properties to the GC AlSi10Mg sheet due to the mixed strengthening mechanism among strengthening phase precipitation, grain structure and dynamic recrystallization (DRX) degree. For instance, the former demonstrates a total elongation (obtained from hot uniaxial tensile tests) of 81.2% and an ultimate bulging height (obtained from the hot biaxial gas bulging tests) of 12.16 mm; in contrast, the latter's elongation and bulging height are 56.2% and 9.26 mm, respectively. Moreover, the LPBF AlSi10Mg sheet shows more uniform deformation than the GC AlSi10Mg sheet during the bulging tests. The feasibility of forming the LPBF-fabricated preform by HMGF process was confirmed. This lays a foundation for the integrated process of LPBF and HMGF to fabricate complex thin-walled components.

Deformation and control method of thin-walled part during laser powder bed fusion of Ti–6Al–4V alloy

In-situ investigation into the deformation behavior of Ti-6Al-4V processed by laser powder bed fusion

Residual stress of typical parts in laser powder bed fusion

The effect of rescanning strategy on residual stress and deformation of laser-based powder bed fusion of 316L stainless steel thin-walled parts

Effect of processing parameters on the defects, microstructure, and property evaluation of Ti-6Al-4V titanium alloy processed by laser powder bed fusion

Developing ductile and isotropic Ti alloy with tailored composition for laser powder bed fusion

High power laser powder bed fusion of Ti6Al4V alloy: The control of defects, microstructure, and mechanical properties

The influence of building parameters on residual stress, interfacial structure, and cracking control of laser powder bed fusion processed Ti6Al4V/AlMgScZr multi-material parts

Unveiling the impact of layerwise laser preheating on microstructure and mechanical response in laser powder bed fusion

Effects of the process parameters on the formability and properties of Ni54(at.%) Ti alloys prepared by laser powder bed fusion

In-situ control of residual stress and its distribution in a titanium alloy additively manufactured by laser powder bed fusion

Effects of Build Direction and Heat Treatment on the Defect Characterization and Fatigue Properties of Laser Powder Bed Fusion Ti6Al4V

Numerical and experimental investigation of the geometry dependent layer-wise evolution of temperature during laser powder bed fusion of Ti–6Al–4V

Formability and microstructure of laser powder bed fused AlSi10Mg alloy sheets under various deformation conditions

Overlap ratio and scanning strategy effects on laser powder bed fusion Ti6Al4V: numerical thermal modeling and experiments

Formation mechanisms and control strategies of metallurgical defects and microstructures during laser powder bed fusion of AlSi10Mg lattice structures

Influence of Powder Bed Temperature on the Microstructure and Mechanical Properties of Ti-6Al-4V Alloy Fabricated via Laser Powder Bed Fusion

Effect of laser process parameters on thermal behavior and residual stress of high-strength aluminum alloy processed by laser powder bed fusion

The effect of process parameters on the stability and efficiency in the laser powder bed fusion of Ti-6Al-4 V based on the interval powder layer thickness

Stability of molten pool and microstructure evolution of Ti-6Al-4V during laser powder bed fusion with a flat-top beam

Laser Powder Bed Fusion of Titanium Aluminides: An Investigation on Site-Specific Microstructure Evolution Mechanism