Abstract:As the prospective carbon materials, graphene oxide (GO) and carbon nanotubes (CNTs) have attracted extensive attention in the fabrication of copper matrix composites (CMCs), but how their orientation and synergetic effect in Cu matrix affects the properties of composites has not been explored systematically. Herein, an efficient route to fabricate CMCs with GO-CNTs hybrid reinforcement had been reported, as well as the influence of different carbon reinforcement and different current densities on the texture orientation, microstructure and the comprehensive performance were investigated. From ultraviolet–visible results, it was found that one-dimensional CNTs bridge adjacent two-dimensional GO through π-π bonding to form an interconnected network structure. By adding GO-CNTs hybrid reinforcement to pure Cu sulfate, the preferred crystalline orientation of the GO-CNTs/Cu had been changed and a preferred orientation of (111) crystal plane was formed. Meanwhile, the EBSD results revealed that the GO-CNTs hybrid reinforcement had significant grain refinement effect and the average grain size of GO-CNTs/Cu composite reduced to 112 nm. According to TEM images, the lattice stripes between GO and CNTs indicate the formation of C–C covalent bonding. Owing to the synergistic effect and the C–C covalent bonding between GO and CNTs, the highest thermal conductivity reached to 527 W m −1 K −1 , while, the highest hardness was up to 226.8 HV 0.1 , the friction coefficient reduced to 0.62and excellent corrosion resistance of the GO-CNTs/Cu composite were also achieved. This study suggested that the promising fabrication of high-oriented GO-CNTs/Cu composite may have the potential to obtain excellent performance.

Enhancing mechanical properties of pure copper-based materials with CrxOy nanoparticles and CNT hybrid reinforcement

A comparison study of the strengthening effect of carbon nanomaterial reinforcements in the 3D skeleton-reinforced copper matrix composites

Improving mechanical properties of copper composite by interconnected MoO2 quantum dots

Enhancement of ultimate tensile strength and ductility of copper matrix composites using a low content of single-wall carbon nanotubes

Improving comprehensive performance of copper matrix composite by spray pyrolysis fabricated CNT/W reinforcement

Unveiling the Strengthening and Toughening Effects of Copper-Coated Carbon Nanotubes for the Allicu Alloy Matrix Composite

Mechanical and Conductive Properties of Cu Matrix Composites Reinforced by Oriented Carbon Nanotubes with Different Coatings

Enhancement of mechanical properties and conductivity in carbon nanotubes (CNTs)/Cu matrix composite by surface and intratube decoration of CNTs

Realizing the combination of high strength and good ductility of Cu matrix composites with CrCoNi reinforcement particles and microlaminated structure

Toughening and strengthening of Cu-coated carbon nanotubes reinforced AZ61 magnesium matrix nanocomposites by improving interfacial bonding

Enhancement mechanisms of mechanical, electrical and thermal properties of carbon nanotube-copper composites: A review

Achieving good strength‐plasticity compatibility in Cu composites via carbon nanotube (CNT)‐induced heterogeneous bimodal structure

Enhanced Mechanical Properties and High Electrical Conductivity in Multiwalled Carbon Nanotubes Reinforced Copper Matrix Nanolaminated Composites

High strength and electrical conductivity of copper matrix composites reinforced by carbon nanotube-graphene oxide hybrids with hierarchical structure and nanoscale twins

Regulating the mechanical properties and electrical conductivity of CNTs/Cu composites by tailoring nano-sized TiC on the surface of intact CNTs

Enhancing the mechanical and electrical conductivity of copper matrix composites through grafting carbonized polymer dots (CPD) onto carbon nanotube surfaces

Improvement of interfacial interaction and mechanical properties in aluminum matrix composites reinforced with Cu-coated carbon nanotubes

Microstructure, properties and synergetic effect of graphene oxide-functionalized carbon nanotubes hybrid reinforced copper matrix composites prepared by DC electrodeposition

Optimization of the mechanical properties of CNTs/Cu composite by regulating the size of interfacial TiC

Enhanced mechanical, tribological and corrosion properties of graphite and carbon nanotube-reinforced copper-based hybrid composites

A high strength and high electrical conductivity copper based composite enhanced by graphene and Al2O3 nanoparticles