Abstract:A thermodynamic model for open combined Brayton and inverse Brayton cycles is established considering the pressure drops of the working fluid along the flow processes and the size constraints of the real power plant using finite time thermodynamics in this paper. There are 11 flow resistances encountered by the gas stream for the combined Brayton and inverse Brayton cycles. Four of these, the friction through the blades and vanes of the compressors and the turbines, are related to the isentropic efficiencies. The remaining flow resistances are always present because of the changes in flow cross-section at the compressor inlet of the top cycle, combustion inlet and outlet, turbine outlet of the top cycle, turbine outlet of the bottom cycle, heat exchanger inlet, and compressor inlet of the bottom cycle. These resistances control the air flow rate and the net power output. The relative pressure drops associated with the flow through various cross-sectional areas are derived as functions of the compressor inlet relative pressure drop of the top cycle. The analytical formulae about the relations between power output, thermal conversion efficiency, and the compressor pressure ratio of the top cycle are derived with the 11 pressure drop losses in the intake, compression, combustion, expansion, and flow process in the piping, the heat transfer loss to the ambient, the irreversible compression and expansion losses in the compressors and the turbines, and the irreversible combustion loss in the combustion chamber. The performance of the model cycle is optimized by adjusting the compressor inlet pressure of the bottom cycle, the air mass flow rate and the distribution of pressure losses along the flow path. It is shown that the power output has a maximum with respect to the compressor inlet pressure of the bottom cycle, the air mass flow rate or any of the overall pressure drops, and the maximized power output has an additional maximum with respect to the compressor pressure ratio of the top cycle. When the optimization is performed with the constraints of a fixed fuel flow rate and the power plant size, the power output and efficiency can be maximized again by properly allocating the fixed overall flow area among the compressor inlet of the top cycle and the turbine outlet of the bottom cycle.

Maximizing work of finite-potential-reservoir isothermal-chemical-engines with generalized models of bypass-mass-leakage and mass-resistance

FEA-Based Mathematical Modeling and Simulation for IPMSM Drive with Consideration of Saturation and Cross-Coupling Influence

Power maximization for multistage endoreversible non-isothermal-chemical-engine based on Lewis analogy

Conceptual Design and Optimization of Scramjet Engines Using the Exergy Method

Simultaneous Optimization for Organic Rankine Cycle Design and Heat Integration

Optimal Criteria for Different Parameters of an Irreversible Regenerative Intercooled Brayton Cycle under Maximum Power and Maximum Ecological COP Conditions

Heat Engine Cycle Configurations for Maximum Work Output with Generalized Models of Reservoir Thermal Capacity and Heat Resistance

Power output and efficiency optimization of endoreversible non-isothermal chemical engine via Lewis analogy

Optimal Configuration of Finite Source Heat Engine Cycle for Maximum Output Work with Complex Heat Transfer Law

Four-Objective Optimization of an Irreversible Magnetohydrodynamic Cycle

Multi-objective optimization for an irreversible Braysson cycle

Power and efficiency optimization for combined Brayton and inverse Brayton cycles

Thermodynamic Assessment on Performance Extremes of the Fuel Indirect Precooled Cycle for Hypersonic Airbreathing Propulsion

Analysis of Impact of Control Strategies on Integrated Electric Propulsion System Performance During Icebreaking Process

Unsteady Analysis of A Bottoming Organic Rankine Cycle for Exhaust Heat Recovery from an Internal Combustion Engine Using Monte Carlo Simulation

Effect of non-ideal gas working fluid on power and efficiency performances of an irreversible Otto cycle

Power and Thermal Efficiency Optimization of an Irreversible Steady-Flow Lenoir Cycle

Optimization Design of Progressive Cavity Pumps via Finite Element Simulations with a Fluid-Solid Interaction Model

Power, Efficiency, Entropy-Generation Rate and Ecological Optimization for a Class of Generalized Irreversible Universal Heat-Engine Cycles

Performance Analysis and Optimization of a Combined Cooling and Power System Using Low Boiling Point Working Fluid Driven by Engine Waste Heat

Power Density Analysis and Multi-Objective Optimization for an Irreversible Dual Cycle