Abstract:Implementation of metal organic frameworks (MOFs) in the separation science has attracted many researchers attention. In this study, the role of metal, ligand, the reaction condition and modification on the extraction efficiency of some MOFs was investigated. Among the prevalent reported MOFs, some members of the MIL and MOF-5 families were chosen, and eleven MOF-based sorbents were prepared by changing the metal and ligand type, reaction condition, and/or functionality through post synthetic modification (PSM). MIL-101 and MIL-101-NH2 based structures were initially synthesized based on the chromium and iron salts. Also, three zinc-based structures including MOF-5, [NH2(CH3)2]2 [Zn3(C6H4(CO2)2)4].DMF.H2O and [NH2(CH3)2]2 [Zn3((C6H4)2(CO2)2)4].5DMF were synthesized. The PSM hydrophobic-oriented products of MILs were obtained by their reactions with benzyl alcohol. The resulted MOFs were characterized by FT-IR, PXRD, SEM, BET, BJH, water contact angle and TG analyses. The extraction trends of these nanostructures were studied toward some priority environmental pollutants such as polycyclic aromatic hydrocarbons (PAHs), chlorobenzenes (CBs), and benzene homologs. The extraction procedures were performed via adapting a home-made headspace needle trap extraction (HS-NTE) setup, and determinations were followed by gas chromatography-mass spectrometry (GC-MS). Among all the synthesized nanostructures, the chromium-based PSM product of MIL-101-NH-CH2C6H5 proves its improved extraction capability for most of the model compounds. Eventually, the superior MOF was applied as the extractive phase in a HS-NTE-GC-MS method for isolation and trace determination of PAHs, in tea, coffee, and some other environmental water samples. Under the optimized conditions, the linear dynamic range (LDR) was in the range of 1-1000 ng L-1 (R2 > 0.992) while the limits of detection (LOD) and limits of quantification (LOQ) values were 0.1-0.2 and 0.3-0.7 ng L-1, respectively. Also, the extraction capability of the Cr-based MIL-101-NH-CH2C6H5 was compared with commercial polydimethyl siloxane-divinyl benzene (PDMS-DVB) fiber coating. The intra-and inter-day relative standard deviations for three replicates at the concentration levels of 20 and 500 ng L-1 were in the range of 4-7% and 5-10%, respectively. The needle-to-needle reproducibility was also found to be in the range of 6-10%. Acceptable relative recovery values at the concentration levels of 20 and 500 ng L-1 ranged from 89 to 98%, showing no significant matrix effect.

Modulating the selectivity of solid-phase microextraction fibers based on morphological, compositional, and size-depended control of bimetallic oxide nanostructures grown on nickel-titanium alloy substrates

Development of a novel porous cobalt, phosphorus and nitrogen co-doped carbonaceous coating by phosphiding ZIF-67 grown on nitinol fiber for selective solid-phase microextraction of polycyclic aromatic hydrocarbons from water samples

Electrochemical In Situ Fabrication of Titanium Dioxide Nanotubes on a Titanium Wire as a Fiber Coating for Solid-Phase Microextraction of Polycyclic Aromatic Hydrocarbons

Biochar nanosphere- and covalent organic framework nanosphere-functionalized titanium dioxide nanorod arrays on carbon fibers for solid-phase microextraction of organic pollutants

Preparation of a new coating of graphene oxide/nickel complex on a nickelized metal surface for direct immersion solid phase microextraction of some polycyclic aromatic hydrocarbons

Titania hybridized melamine–formaldehyde aerogel for online in-tube solid-phase microextraction of polycyclic aromatic hydrocarbons prior to HPLC–DAD

MOF-derived porous carbon microspheres Ni@C-acid as solid-phase microextraction coating for extraction of polycyclic aromatic hydrocarbons from tea infusions

Morphology, composition and selectivity of nickel/titanium oxide nanoflakes grown on a superelastic nickel/titanium alloy fiber substrate for highly efficient solid-phase microextraction of aromatic compounds

A solid-phase microextraction fiber with carbon nanoparticles as sorbent material prepared by a simple flame-based preparation process

Roles of metal, ligand and post synthetic modification on metal organic frameworks to extend their hydrophobicity and applicability toward ultra-trace determination of priority organic pollutants

Application of Diphenyl Functionalization of Nickel Foam as Dispersive Solid-Phase Extraction Adsorbent to Polycyclic Aromatic Hydrocarbon Contaminants in Chinese Herbal Medicines

Nanoleaf-derived carbon materials as a sensitivity coating for solid‑phase microextraction of polycyclic aromatic hydrocarbons

Controllable in situ growth of novel octahedral TiO 2 nanoparticles on nickel/titanium alloy fiber substrate for selective solid-phase microextraction of ultraviolet filters in water samples

The extraction of polycyclic aromatic hydrocarbons from water samples with aromatic-dithiocarbamate modified magnetic nanoparticles

A solid-phase microextraction fiber coating based on magnetic covalent organic framework for highly efficient extraction of triclosan and methyltriclosan in environmental water and human urine samples

Silver nanoparticle-functionalized melamine-formaldehyde aerogel for online in-tube solid-phase microextraction of polycyclic aromatic hydrocarbons followed by HPLC-DAD analysis

Flower-like Co3O4/C3N5 composite as solid-phase microextraction coating for high-efficiency adsorption and preconcentration of polycyclic aromatic hydrocarbons and polychlorinated biphenyls in water

Ultrasonic assisted synthesis of a novel ternary nanocomposite based on carbon nanotubes/zeolitic imidazolate framework-67/polyaniline for solid-phase microextraction of organic pollutants

Exploring New Extractive Phases for In-Tube Solid Phase Microextraction Coupled to Miniaturized Liquid Chromatography

Hierarchically spherical assembly of carbon nanorods derived from metal-organic framework as solid-phase microextraction coating for nitrated polycyclic aromatic hydrocarbon analysis

Hierarchical covalent organic framework hollow nanofibers-bonded stainless steel fiber for efficient solid phase microextraction