Abstract:With the development in additive manufacturing, the use of surface treatments for gas turbine design applications has greatly expanded. An experimental investigation of the pressure loss and heat transfer characteristics within impingement jet arrays with arrays of target surface micro cooling units is presented. The discharge coefficient and Nusselt number are measured and determined for an evaluation of the pressure loss of the flow system and heat transfer level, respectively. Considered are effects of impingement jet Reynolds number ranging from 1000 to 15,000 and micro cooling units (square pin fin) height (h) with associated values of 0.01, 0.02, 0.05, 0.2, and 0.4 D, where D is the impingement hole diameter. Presented are variations of Nusselt number, and Nusselt number ratio, discharge coefficient, discharge coefficient ratio, discharge coefficient correlation. Depending upon the micro cooling unit height, discharge coefficient ratios slightly decrease with height, and the ratio values generally remain unit value (1.0). When Rej = 1000 and 2500 for several cooling units height values, discharge coefficient ratios show the pressure loss decreases about 2–18% and 3–6%, respectively, when compared to the data of a baseline smooth target surface plate. The observed phenomenon is due to the effects of flow blockage of micro cooing units, local flow separation, and near-wall viscous sublayer reattachment. Results also show that heat transfer levels increase 20–300% for some of the tested toughened target surface plates when compared to smooth target surface plates. The heat transfer level enhancement is because of an increase in thermal transport and near-wall mixing, as well as the increased wetted area. In addition, micro cooling units elements break the viscous sublayer and cause greater turbulence intensity when compared to the smooth target surface. Overall, results demonstrate that the target surface micro cooling units do not result in a visible increment in pressure loss and reduce pressure loss of the flow system for some of the tested patterns. Moreover, results show the significant ability of micro cooling units to enhance the surface heat transfer capability of impingement cooling relative to smooth target surfaces.

Tomographic flow measurements over additively manufactured cooling channel roughness

Flow Through a Passage With Scaled Additive Manufacturing Roughness Representing Different Printing Orientations

HIGH-FIDELITY COMPUTATIONAL ASSESSMENT OF AERO-THERMAL PERFORMANCE AND THE REYNOLDS' ANALOGY FOR ADDITIVELY MANUFACTURED ANISOTROPIC SURFACE ROUGHNESS

Scaling Roughness Effects on Pressure Loss and Heat Transfer of Additively Manufactured Channels

Direct Numerical Simulation of Channel Flow with Real Surface Roughness Using a Ghost Cell Immersed Boundary Method

Large Eddy Simulations of Flow over Additively Manufactured Surfaces: Impact of Roughness and Skewness on Turbulent Heat Transfer

Large Eddy Simulations of Fully-Developed Turbulent Flows Over Additively Manufactured Rough Surfaces

Heat transfer enhancement with additively manufactured rough surfaces: Insights from large-eddy simulations

Large Eddy Simulation of Film Cooling for the Real Additive Manufactured Fan-Shaped Holes

Experimental Investigation of Micro Cooling Units on Impingement Jet Array Flow Pressure Loss and Heat Transfer Characteristics

Thermo-Hydraulic Characteristics of Micro-Scale Surface Roughness Topology of Additively Manufactured Surface Model: Modal Decomposition Perspective

Experimental Assessment of Hypersonic Convective Heat Transfer Augmentation due to Surface Roughness

Understanding heat transfer and flow characteristics of additively manufactured pin fin arrays through laser-induced fluorescence and particle image velocimetry

Additive manufacturing of scalable jet impingement and radial taper enhancements for improved flow boiling performance

Friction factor and heat transfer prediction of rocket engine cooling channels in numerical simulations with high roughness Reynolds number

Influences of Laser Incidence Angle and Wall Thickness on Additive Components

Heat Transfer and Pressure Loss of Turbulent Flow in a Wedge-Shaped Cooling Channel with Different Types of Triply Periodic Minimal Surfaces

IMPACTS OF SUPERALLOYS ON THE SURFACE QUALITY OF ADDITIVELY MANUFACTURED CHANNELS

Analysis of Film Cooling Effectiveness for Jet in Crossflow with Upstream and Downstream Roughness

Uncertainty Quantification of Film Cooling Performance of an Industrial Gas Turbine Vane

Film Cooling Performances Under Various Upstream Roughness Conditions: Experimental Investigations and Similarity Hypothesis