Abstract:This graphical abstract presents a low‐power, high dynamic range second‐order delta‐sigma modulator (DSM) for sensing applications. The DSM employs a hybrid CIFF‐B architecture, consisting of a continuous‐time first stage and a discrete‐time second stage. The first stage, an OTA‐based RC integrator with anti‐aliasing properties, is chopped to mitigate offset and 1/f noise, while the second stage employs a switched‐capacitor integrator with OTA‐sharing to reduce complexity and enable signal addition before quantization. Fabricated in a 180‐nm CMOS process, the DSM achieves a 103 dB dynamic range in a 100 Hz bandwidth, with peak SNDR, SNR, and SFDR values of 95.8 dB, 97.1 dB, and 102.8 dB, respectively, and consumes 10.7 μ A from a 1.8 V supply. The Schreier figure‐of‐merit (FoMs) is 170.2 dB, highlighting its energy efficiency. This paper reports a low‐power, high dynamic range second‐order delta‐sigma modulator (DSM) for sensing applications. The DSM employs a hybrid CIFF‐B topology, consisting of a continuous‐time first stage and a discrete‐time second stage. The first stage is an OTA‐based RC integrator with inherent anti‐aliasing properties, while the second stage is a switched‐capacitor integrator. Offset and 1/f noise in the first stage are mitigated by the chopper‐stabilization technique, while those in the second stage are suppressed through the gain provided by the first stage. Furthermore, the OTA‐sharing technology is utilized in the second stage to realize signal addition before quantization, reducing design complexity. The hybrid DSM prototype is fabricated with a 180‐nm CMOS process and occupies an area of 0.123 mm2. Measurement results show peak SNDR/SNR/SFDR values of 95.8, 97.1, and 102.8 dB, respectively, with a current consumption of 10.7 μ A from a 1.8‐V single supply. The reported DSM achieves a 103‐dB dynamic range in a 100‐Hz signal bandwidth, corresponding to a Schreier figure‐of‐merit (FoMs) value of 170.2 dB.

A 23.7‐uW 93.5‐dB SNDR delta‐sigma modulator for healthcare and medical diagnostics

A 10.7-Μa 103-Db DR Hybrid Delta-Sigma Modulator for Sensing Applications

An 18-Bit 2-2 MASH Delta-Sigma Modulator for Isolated Amplifier

A 65-Nm Low-Noise Low-Cost ΣΔ Modulator for Audio Applications

Low-power High-Linearity Sigma-Delta Modulator for Audio Applications

A High-Performance,Low-Power ΣΔ Modulator for Digital Audio Applications

A 0.18 Μm High Resolution Bandpass Delta-Sigma Modulator for Acceleration Transducer Applications

A 0.18 μm Single-poly CMOS ∑-△ Modulator for Digital Audio Applications

A 10.7‐μ A 103‐dB DR Hybrid Delta‐Sigma Modulator for Sensing Applications

0.9 V 58 Μw 92 Db SNDR Audio ΔΣ Modulator with High Efficiency Low Noise Switched-Opamp and Novel DWA Technique

A 1.1V 12μw 86db DR Sigma-Delta Modulator for Health Monitoring System

A Low Power Audio Delta-Sigma Modulator with Opamp-Shared and Opamp-Switched Techniques

A 1.2 V 2.3 Μw 94.7 Db DR Delta-Sigma Modulator with Dynamic-Range Enhancement and Tri-Level CDAC

A 10-Khz BW 104.3-Db DR Discrete-Time Delta-Sigma Modulator with Ring-Amplifier-based Integrator

A 1V low power second-order delta-sigma modulator for biomedical signal application

A 1.44-mW 96-dB SNR Sigma-Delta modulator with low-power OPAMP

A 0.8-V 230-$\mu$ W 98-dB DR Inverter-Based $\Sigma \Delta$ Modulator for Audio Applications.

A 0.6V 19.5 mu W 80 dB DR Delta Sigma Modulator with SA-Quantizers and Digital Feedforward Path

Low‐power multibit delta–sigma modulator based on passive and unattenuated summation scheme

A 400 mV 160 nW/Ch Compact Energy Efficient ∆Σ Modulator for Multichannel Biopotential Signal Acquisition System

A 112db SNDR Delta-Sigma Modulator for Low-Power Audio Applications