Abstract:Soft magnetic Fe-Al alloys have been a subject of research in the past. However, they never saw the same reception in technical applications as the Fe-Si or Fe-Ni alloys, which is, to some extent, due to a low ductility level and difficulties in manufacturing. Additive manufacturing (AM) technology could be a way to avoid issues in conventional manufacturing and produce soft magnetic components from these alloys, as has already been shown with similarly brittle Fe-Si alloys. While AM has already been applied to certain Fe-Al alloys, no magnetic properties of AM Fe-Al alloys have been reported in the literature so far. Therefore, in this work, a Fe-12Al alloy was additively manufactured through laser powder bed fusion (L-PBF) and characterized regarding its microstructure and magnetic properties. A comparison was made with the materials produced by casting and rolling, prepared from melts with an identical chemical composition. In order to improve the magnetic properties, a heat treatment at a higher temperature (1300 °C) than typically applied for conventionally manufactured materials (850–1150 °C) is proposed for the AM material. The specially heat-treated AM material reached values (HC: 11.3 A/m; μmax: 13.1 × 103) that were close to the heat-treated cast material (HC: 12.4 A/m; μmax: 20.3 × 103). While the DC magnetic values of hot- and cold-rolled materials (HC: 3.2 to 4.1 A/m; μmax: 36.6 to 40.4 × 103) were not met, the AM material actually showed fewer losses than the rolled material under AC conditions. One explanation for this effect can be domain refinement effects. This study shows that it is possible to additively manufacture Fe-Al alloys with good soft magnetic behavior. With optimized manufacturing and post-processing, further improvements of the magnetic properties of AM L-PBF Fe-12Al may still be possible.

Microstructure and magnetic domain structure of additively manufactured Fe–Si soft magnetic alloys with 3 and 9 wt.-% Si

Development of FeSi steel with increased Si content by laser powder bed fusion technology for ferromagnetic cores application: Microstructure and properties

Binder jet additive manufacturing method to fabricate near net shape crack-free highly dense Fe-6.5 wt.% Si soft magnets

Additive manufacturing of Fe-3.5 wt.-%Si electrical steel via laser powder bed fusion and subsequent thermomechanical processing

The Microstructure and Magnetic Properties of a Soft Magnetic Fe-12Al Alloy Additively Manufactured via Laser Powder Bed Fusion (L-PBF)

Magnetic and mechanical properties of additive manufactured Fe-3wt.%Si material

Microstructure and soft magnetic properties of nanocrystalline Fe–Si powders

Investigation of Soft Magnetic Material Fe-6.5Si Fracture Obtained by Additive Manufacturing

Evaluation of Microstructure, Mechanical and Magnetic Properties of Laser Powder Bed Fused Fe-Si Alloy for 3D magnetic flux motor application

Additive Manufacturing: A New Concept For End Users. The Case Of Magnetic Materials

Additive manufacturing of soft magnetic materials and components

Improving the soft magnetic properties of binder jet printed iron-silicon alloy through boron addition

Surface Modification and Its Role in the Preparation of FeSi Gradient Alloys with Good Magnetic Property and Ductility

Microstructure and magnetic properties of FeSiBCrC soft magnetic alloy manufactured by selective laser melting

Computational study on microstructure evolution and magnetic property of laser additively manufactured magnetic materials

Microstructure and tribological property of laser melt deposited α/Fe9Cr9Si2 metal silicide alloys

Near net shape fabrication of anisotropic Fe-6.5%Si soft magnetic materials

Study on solidification organization and phase formation of Fe-6.5wt.%Si high silicon steel by arc melting and heat treatment

Design of Fe-based nanocrystalline alloys with superior magnetization and manufacturability

The influence of cooling rate on microstructure and magnetic properties of cast Fe-6.5wt%Si steel

Twin Roll Casting and Secondary Cooling of 6.0 wt.% Silicon Steel