Abstract:Human being faces two key problems: world-wide energy shortage and global climate worming. To reduce energy consumption and carbon emission, it needs to develop high efficiency heat transfer devices. In view of the fact that the existing enhanced technologies are mostly developed according to the experiences on the one hand, and the heat transfer enhancement is normally accompanied by large additional pumping power induced by flow resistances on the other hand, in this chapter, the field synergy principle for convective heat transfer optimization is presented based on the revisit of physical mechanism of convective heat transfer. This principle indicates that the improvement of the synergy of velocity and temperature gradient fields will raise the convective heat transfer rate under the same other conditions. To describe the degree of the synergy between velocity and temperature gradient fields a non-dimensional parameter, named as synergy number, is defined, which represents the thermal performance of convective heat transfer. In order to explore the physical essence of the field synergy principle a new quantity of entransy is introduced, which describes the heat transfer ability of a body and dissipates during hear transfer. Since the entransy dissipation is the measure of the irreversibility of heat transfer process for the purpose of object heating the extremum entransy dissipation (EED) principle for heat transfer optimization is proposed, which states: for the prescribed heat flux boundary conditions, the least entransy dissipation rate in the domain leads to the minimum boundary temperature difference, or the largest entransy dissipation rate leads to the maximum heat flux with a prescribed boundary temperature difference. For volume-to-point problem optimization, the results indicate that the optimal distribution of thermal conductivity according to the EED principle leads to the lowest average domain temperature, which is lower than that with the minimum entropy generation (MEG) as the optimization criterion. This indicates that the EED principle is more preferable than the MEG principle for heat conduction optimization with the purpose of the domain temperature reduction. For convective heat transfer optimization, the field synergy equations for both laminar and turbulent convective heat transfer are derived by variational analysis for a given viscous dissipation (pumping power). The optimal flow fields for several tube flows were obtained by solving the field synergy equation. Consequently, some enhanced tubes, such as, alternation elliptical axis tube, discrete double inclined ribs tube, are developed, which may generate a velocity field close to the optimal one. Experimental and numerical studies of heat transfer performances for such enhanced tubes show that they have high heat transfer rate with low increased flow resistance. Finally, both the field synergy principle and the EED principle are extended to be applied for the heat exchanger optimization and mass convection optimization.

Nature-Inspired Structures Applied in Heat Transfer Enhancement and Drag Reduction

Thermohydraulic Performance Optimization of Integrated Porous Pin Fins in Microchannel Heat Sink Using Shape Optimization Coupled with NSGA

Design and Optimization of Additive Manufactured Fischer-Koch-structured Heat Exchanger for Enhanced Heat Transfer Efficiency

Enhancing Plate-Fin Heat Exchanger Hydraulic Thermal Performance Through Air-Side Fin Optimization Based on Pseudo-3D Topology Optimization

107 Collaborative Project of Heat Transfer Enhancement by Nano- and Micro-Scale Porous Layers Formed on Surface

Flow and heat transfer performance of bionic heat transfer structures with hybrid triply periodic minimal surfaces

Optimization of Bionic Heat Sinks with Self-Organized Structures Inspired by Termite Nest Morphologies

The Global Optimal Structural Morphogenesis for Heat Conduction

Optimization of H-type finned tube heat exchangers with combinations of longitudinal vortex generator, dimples/protrusions and grooves by Taguchi method

Advanced Design and Manufacturing Approaches for Structures with Enhanced Thermal Management Performance: A Review

Numerical and Experimental Investigation of Additive Manufactured Heat Exchanger Using Triply Periodic Minimal Surfaces (TPMS)

Biomimetic Groundwork for Thermal Exchange Structures Inspired by Plant Leaf Design

Numerical investigation and optimization of flat plate transpiration-film combined cooling structure

Heat Transfer Enhancement of Wedge-Shaped Channels Using the Interpretable Multi-Objective Generative Design Method

Numerical and Visual Performance Investigation of a Plate Heat Exchanger Designed by Topological Optimization

Heat Transfer Enhancement Mechanics of Different Micro-Disturbing Structures for Transcritical Hydrocarbon Fuel Using 3-D Secondary Flow Intensity Analysis

Optimization Principles For Heat Convection

Numerical Study on Flow and Heat Transfer Performance of Rectangular Heat Sink with Compound Heat Transfer Enhancement Structures

Thermal management of electronic components based on new wave bio-inspired structures and nanofluids

Application of Combined Enhanced Techniques for Design of Highly Efficient Air Heat Transfer Surface

Numerical Simulation and Thermodynamic Test Analysis of Plate Heat Exchanger Based on Topology Optimization