Abstract:AlCoCrFeNi is one of the early studied high-entropy alloys (HEAs), attracting considerable attention due to its attractive mechanical properties. Efforts have been continuously made improve properties of the HEA by modifying its composition. In this study, WC particles were added to AlCoCrFeNi alloy with different percentages (10, 30 and 60 wt.%) using an arc furnace. Since medium-entropy alloys with fewer elements may also possess attractive properties with less structural complication, we also added WC to Co-free medium-entropy alloy, AlCrFeNi, in comparison with its high-entropy HEA companion. Microstructure, mechanical properties and resistances against wear, corrosion and corrosive wear of the WC-added alloys were investigated. It was shown that the added WC decomposed and formed in situ carbides. The WC-added AlCrFeNi is harder with a higher wear resistance than the WC-added AlCoCrFeNi. Both the alloys consist of a BCC matrix and carbides in a eutectic state. With increasing the WC content, hardness and wear resistance of the alloys increased. The medium-entropy alloy AlCrFeNi showed better performance than AlCoCrFeNi. For comparison, Co-WC composite alloy was also made using the arc furnace. The wear volume loss of AlCrFeNi-60 wt.%WC was only half of that of Co-60 wt.%WC under the same wearing condition. The corrosion resistance of the Co-containing alloy, e.g., AlCoCrFeNi+60WC, showed its corrosion resistance lower than that of Co-free AlCrFeNi-60 wt.%WC, mainly due to its lower %Cr. The addition of WC also significantly reduced the volume loss caused by corrosive wear in the 3.5 wt.% NaCl solution for both alloys.

Effects of NbC addition on mechanical and tribological properties of AlCrFeNi medium-entropy alloy

Effect of Submicron SiC Particles on the Properties of Alcocrfeni High Entropy Alloy Coatings

In-situ (Nb,Ti)C particles reinforced Ni0.6CoFe1.4Nb0.05 medium-entropy alloys

Development and Characterization of CrCoNi Medium Entropy Alloy Particles Reinforced Aluminum Matrix Composite

Wear Properties of Spark Plasma-Sintered AlCoCrFeNi2.1 Eutectic High Entropy Alloy with NbC Additions

Mechanical and dry sliding tribological properties of CoCrNiNb medium-entropy alloys at room temperature

Effect of Aluminum on the Friction and Wear Behavior of AlxCrFeNi Medium‐Entropy Alloys

Effect of C additions to the microstructure and wear behaviour of CoCrFeNi high-entropy alloy

Microstructure, mechanical properties, and wear behavior of AlCoCrFeNi high-entropy alloy and AlCrFeNi medium-entropy alloy with WC addition

Effect of WC addition on microstructure and properties of powder metallurgy CoCrNi medium entropy alloy

An atomic insight into the stoichiometry effect on the tribological behaviors of CrCoNi medium-entropy alloy

Effect of Al Addition on Microstructure and Properties of CoCrNi Medium-Entropy Alloy Prepared by Powder Metallurgy

Microstructures and mechanical properties of in-situ FeCrNiCu high entropy alloy matrix composites reinforced with NbC particles

Influence of Cu and Co addition on metallurgical and wear characteristics of AlCrFeNi high entropy alloy

Investigation of Mechanical Properties and Wear Resistance of A2/B2 Type Medium-Entropy Alloy Matrix Reinforced with Tungsten Particles by In-Situ Reaction

A non-equiatomic Ni-Co-Fe medium-entropy alloy with excellent wear resistance and strength-ductility combination by adding Al

Effects of niobium on the microstructure, corrosion, and mechanical behavior of ultra-fine lamellar Al 0.3 CrFeCoNiNb x eutectic high-entropy alloys

Improving wear and corrosion resistance of LDEDed CrFeNi MEA through addition of B and Si

Effect of Cr3C2 Addition on Microstructure and Mechanical Properties of WC-CoNiFe Cemented Carbides

Effects of Nb and Zr Alloying on the Microstructure, Mechanical Properties, and Corrosion Resistance of CoCrFeNi High-Entropy Alloys

The effect of Co substitutions for Ni on microstructure, mechanical properties and corrosion resistance of Fe50Mn25Cr15Ni10 medium-entropy alloy