Abstract:Dry reforming of methane is one of the few chemical reactions which can effectively convert carbon dioxide (CO2), a major green-house gas, into a valuable chemical precursor, syngas (a mixture of CO and H2), that can be converted into chemicals and fuels via different synthesis routes such as the Fischer Tropsch synthesis. The inherent limitations of dry reforming reaction, for instance, rapid catalyst deactivation by coke deposition and the very high energy requirements, has restricted its use as a commercial technology. This study was performed to evaluate the potential of overcoming the limitations of dry reforming by integrating it with other commercial methane reforming technologies such as steam reforming and partial oxidation reforming in the context of industrial operating conditions. A thermodynamic and kinetic analysis of the combined reforming has been conducted using the software suite MATLAB®. The aim of this complicated assessment is to identify optimized combination of the three reformers and also the corresponding operating conditions that would utilize significant amount of CO2 while ensuring CO2 fixation, minimum carbon formation and optimum energy requirements. The thermodynamic equilibrium product distribution calculations involved the Peng Robinson (PR), Redlich Kwong (RK) and Soave Redlich Kwong (SRK) equations of state (EOS) to identify the best EOS that accounts for the non-ideality associated with the high pressure operation. The study evaluated simultaneous effects of temperature (200°C–1200°C), pressure (1–20bar) and feed mole ratios (of methane, steam, carbon dioxide and oxygen) on the equilibrium product distribution. The addition of oxygen and steam to dry reforming helped in decreasing energy requirements while simultaneously increasing the syngas yield ratio (H2:CO ratio). The numerical evaluation revealed an optimized operating condition of ∼750°C at 1bar pressure at a feed mole ratio CH4:H2O:O2:CO2 of 1:0.4:0.3:1. For this optimization, the system boundaries were limited only to a reformer block without considering the upstream and dowstream processes. At this optimized condition, the carbon deposition was eliminated and the CO2 conversion was observed to be 47.84% with an energy requirement of 180.26kJ. The study is further extended to include kinetic analysis of combined dry and steam reforming of methane. The preliminary findings of kinetic evaluation indicated an excellent agreement between combined kinetic model with the thermodynamic equilibrium results.

Kinetic Analysis of Rate Data for Dry Reforming of Methane

Kinetic Study of Reactive Sorption-Enhanced Reforming of Coke Oven Gas for Hydrogen Production

Kinetic models for the methanation of COx gases to produce methane: A critical analysis

Autothermal reforming of methane on rhodium catalysts: Microkinetic analysis for model reduction

The Intrinsic Kinetics of Methane Steam Reforming over a Nickel-Based Catalyst in a Micro Fluidized Bed Reaction System

Kinetic Analysis of Catalytic Dry Reforming of Methane Using Ni-ZrO2/MCM-41 Catalyst

Density Functional Theory-Assisted Microkinetic Analysis of Methane Dry Reforming on Ni Catalyst

Dry reforming of methane with a Ni-based catalyst: a kinetic and thermodynamic analysis

Kinetic and DRIFTS studies of the CO2 catalytic hydrogenation on Ru/SiO2: A comprehensive and strategic investigation of CO2 methanation mechanisms by kinetic modeling and data regression

Kinetics and mechanistic studies of methane dry reforming over Ca promoted 1Co–1Ce/AC-N catalyst

Intrinsic kinetics of CO2 methanation on low-loaded Ni/Al2O3 catalyst: Mechanism, model discrimination and parameter estimation

Simplified kinetic model for steam reforming of ethanol on a Ni/Al2O3 catalyst

KINETICS STUDY OF METHANOL STEAM REFORMING HYDROGEN PRODUCTION IN A MICROREACTOR

Kinetic Study of Zirconia-Alumina-Supported Ni-Fe Catalyst for Dry Reforming of Methane: Impact of Partial Pressure and Reaction Temperature

Catalytic Reactivity Assessment of AgM and CuM (M = Cr, Fe) Catalysts for Dry Reforming of Methane Process with CO2

DFT studies of dry reforming of methane on Ni catalyst

Development of an Improved Kinetic Model for CO2 Hydrogenation to Methanol

Methane Combustion Kinetics over Palladium-Based Catalysts: Review and Modelling Guidelines

Kinetics of the steam reforming of methane with iron, nickel, and iron-nickel alloys as catalysts

Mechanistic Kinetic Modelling Framework for the Conversion of Waste Crude Glycerol to Value-Added Hydrogen-Rich Gas

A combined thermo-kinetic analysis of various methane reforming technologies: Comparison with dry reforming