Abstract:Introduction: In developed countries, the age structure of the population is currently undergoing an upward shift, resulting a decrease in general bone quality and surgical durability. Over the past decade, oblique lumbar interbody fusion (OLIF) has been globally accepted as a minimally invasive surgical technique. There are several stabilization options available for OLIF cage fixation such as self-anchored stand-alone (SSA), lateral plate-screw (LPS), and bilateral pedicle screw (BPS) systems. The constructs’ stability are crucial for the immediate and long-term success of the surgery. The aim of this study is to investigate the biomechanical effect of the aforementioned constructs, using finite element analysis with different bone qualities (osteoporotic and normal). Method: A bi-segmental (L2–L4) finite element (FE) model was created, using a CT scan of a 24-year-old healthy male. After the FE model validation, CAD geometries of the implants were inserted into the L3–L4 motion segment during a virtual surgery. For the simulations, a 150 N follower load was applied on the models, then 10 Nm of torque was used in six general directions (flexion, extension, right/left bending, and right/left rotation), with different bone material properties. Results: The smallest segmental (L3–L4) ROM (range of motion) was observed in the BPS system, except for right bending. Osteoporosis increased ROMs in all constructs, especially in the LPS system (right bending increase: 140.26%). Osteoporosis also increased the caudal displacement of the implanted cage in all models (healthy bone: 0.06 ± 0.03 mm, osteoporosis: 0.106 ± 0.07 mm), particularly with right bending, where the displacement doubled in SSA and LPS constructs. The displacement of the screws inside the L4 vertebra increased by 59% on average (59.33 ± 21.53%) due to osteoporosis (100% in LPS, rotation). BPS-L4 screw displacements were the least affected by osteoporosis. Conclusions: The investigated constructs provide different levels of stability to the spine depending on the quality of the bone, which can affect the outcome of the surgery. In our model, the BPS system was found to be the most stable construct in osteoporosis. The presented model, after further development, has the potential to help the surgeon in planning a particular spinal surgery by adjusting the stabilization type to the patient’s bone quality.

Virtual modelling the impact of torsional loading on osteoporotic vertebrae buckling

A Predictive Model for Creep Deformation Following Vertebral Compression Fractures

Effects of Bone Damage on Creep Behaviours of Human Vertebral Trabeculae

[Three-Dimensional Finite Element Model of Thoracolumbar Spine with Osteoporotic Vertebral Compression Fracture].

Experimental validation of finite element analysis of human vertebral collapse under large compressive strains

A COMPARATIVE ANALYSIS OF THE EFFECTS OF TWO AUGMENTERS ON THE SENSITIVITY OF VERTEBRAL BIOMECHANICAL BEHAVIOR IN VERTEBROPLASTY

Analysis of the physiological load on lumbar vertebrae in patients with osteoporosis: a finite-element study

Osteocyte-viability-based Simulations of Trabecular Bone Loss and Recovery in Disuse and Reloading

Establishment and analysis of thoracicolumber three-dimensional finite element models in normal people and osteoporotic patients

A method for patient-specific evaluation of vertebral cancellous bone strength: in vitro validation

Biomechanical analysis of sandwich vertebrae in osteoporotic patients: finite element analysis

Biomechanical analysis of stabilization for thoracolumbar anterior spinal failure caused by osteolytic lesions, a finite element comparison of direct lateral corpectomy and posterior long segment instrumentation

Stability Evaluation of Different Oblique Lumbar Interbody Fusion Constructs in Normal and Osteoporotic Condition – A Finite Element Based Study

Finite element analysis of vertebroplasty in the osteoporotic T11‐L1 vertebral body: Effects of bone cement formulation

Mechanical impact of regional structural deterioration and tissue-level compensation on proximal femur trabecular bone

Three-dimensional Finite Element Analysis of Optimal Distribution Model of Vertebroplasty.

Sensitivity analysis of biomechanical effect in vertebral body of two different augmenters

Craniocaudal toggling increases the risk of screw loosening in osteoporotic vertebrae

Fluid-solid coupling numerical simulation of entire rat caudal vertebrae under dynamic loading

A multiscale mechanobiological model of bone remodelling predicts site-specific bone loss in the femur during osteoporosis and mechanical disuse

Modeling and experimental validation of trabecular bone damage, softening and densification under large compressive strains