Abstract:Electrochemical reduction of carbon dioxide via CO2 co-electrolysis (CO2ELY) is an essential process to produce non-fossil chemical feedstock acting as CO2 sink. The required electrical energy can be harvested from temporal surplus of renewable energy sources like solar or wind. Employing a bipolar electrolyte membrane (BPM) in forward-bias is a promising approach to mitigate fundamental problems of the current technological fore-runner design that employs an anion exchange membrane (AEM). We employed synchrotron time-resolved X-ray tomographic microscopy (XTM) to study degradation processes in BPM CO2ELY. In forward-bias BPM co-electrolysis, the cation exchange layer (CEL) faces the anode to provide favorable acidic conditions for the oxygen evolution reaction. Such acidic anode allows using pure water as electrolyte eliminating the salt precipitation at the cathode observed for AEM CO2ELY. As the second major issue in AEM CO2ELY, (bi)carbonate ions formed at the cathode are transported to the anode presenting a major obstacle for high CO2 conversion efficiency. The then required effort to separate CO2 from the electrolyte further reduces the overall energy efficiency. Employing a BPM and introducing the CEL prevents (bi)carbonate ions reaching the anode. BPM CO2ELY retains at the same time the advantages of AEM CO2ELY of performing CO2 reduction under alkaline conditions with the anion exchange layer (AEL) of the BPM facing the cathode. However, BPM CO2ELY suffers from low current density and poor stability in the range of only a few hours. Current limiting factors and degradation processes as well as the affected components are rarely investigated and poorly understood. Processes that have been brought forward are cathode flooding similar to fuel cells or catalyst poisoning. We employ synchrotron XTM to investigate structural dynamics in CO2ELY during operation. The brilliant synchrotron source allows us to acquire one full high-quality scan with a voxel size of 2.75 um in 1 s. We acquired one scan every minute for one hour during electrochemical operation. The image data reveals the formation of gas bubbles at the AEL-CEL junction and ultimately delamination of the BPM. We explain the gas formation as the recombination of (bi)carbonate ions with hydrogen ions at the junction producing gaseous CO2. This CO2 additionally reaches the anode by diffusion causing partial delamination of the anode catalyst layer. CO2 escaping from the AEL surface at the anode forms high-pressure gas bubbles that break the water wet catalyst layer. A diffusive model considering the transport of ions and neutral CO2 is able to capture the mechanism. Our imaging experiments provide insights not attainable by other diagnostic methods and highlight the need for fundamental research on forward-bias BPM CO2ELY. Knowledge based on AEM CO2ELY and fuel cells is not necessarily directly applicable and specific studies on BPM CO2ELY are required to increase performance and stability. We gratefully acknowledge provision of beamtime at TOMCAT, SLS, Paul Scherrer Insititut, Villigen PSI, Switzerland. Figure 1: Tomographic slice of CO2-electrolyser (cathode to the left) a) before operation and running water through anode b) after 23 minutes operation at 3.5V constant potential showing liquid water dynamics at cathode, membrane swelling, gas formation within the membrane and anode catalyst layer disintegration. Figure 1

Dynamics of the Boundary Layer in Pulsed CO2 Electrolysis

Pulsing the Applied Potential in Electrochemical CO 2 Reduction Enhances the C 2 Activity by Modulating the Dynamic Competitive Binding of CO and H

Molecular Level Insights on the Pulsed Electrochemical CO2 Reduction

Dynamic Cation Enrichment during Pulsed CO2 Electrolysis and the Cation-Promoted Multicarbon Formation

Multiscale simulation on electrochemical CO2 reduction in gas-diffusion-electrode-based flow electrolyzer

Two-Phase Flow Model to Define the Mass Transport in a Bicarbonate Electrolyzer for a CO2 Reduction Reaction

Dynamic vs. Stationary Analysis of Electrochemical Carbon Dioxide Reduction: Profound Differences in Local States

Self-Cleaning CO 2 Reduction Systems: Unsteady Electrochemical Forcing Enables Stability

(Invited) Effects of the Local Chemical Environment on the Anode and Cathode Processes of CO2 Electrolyzers

Resolving local reaction environment toward an optimized CO2-to-CO conversion performance

Revealing the In Situ Dynamic Regulation of the Interfacial Microenvironment Induced by Pulsed Electrocatalysis in the Oxygen Reduction Reaction

Structure and dynamics of Li 1.24 K 0.76 CO 3 molten carbonate electrolyte from molecular simulations with explicit polarization

Modeling mass transfer limitations driven by electrowetting in electrochemical CO 2 reduction at silver gas diffusion electrodes

Distinct CO2-run-out Regime from Steric Effect of Electric Double Layer in Electrochemical CO2 Reduction

CO2 Loss into Solution: An Experimental Investigation of CO2 Electrolysis with a Membrane Electrode Assembly Cell

Decoding Double Layer Dynamics for CO2 Electroreduction over Cu

Degradation Processes in Bipolar Membrane CO2-Electrolysis Studied by Time-Resolved X-Ray Tomography

Recovering carbon losses in CO2 electrolysis using a solid electrolyte reactor

Revealing the <i>In Situ</i> Dynamic Regulation of the Interfacial Microenvironment Induced by Pulsed Electrocatalysis in the Oxygen Reduction Reaction

Steering CO2 Electrolysis Selectivity by Modulating the Local Reaction Environment: an Online DEMS Approach for Cu Electrodes

Hierarchically Conductive Electrodes Unlock Stable and Scalable CO2 Electrolysis