Abstract:Numerical modeling of heavily-erbium-doped fluoride fiber lasers is presented. Calculations from the model were compared with all previously reported experimental demonstrations of heavily-erbium-doped fluoride fiber lasers. Commensurate with recent modeling studies, good agreement with the measurements was achieved with the use of scaled-down rate parameters for energy transfer that corresponds to weaker interactions between Er3+ ions. For wavelength-fixed (grating) systems, we show that the measured saturation of the output power results from a combination of changes to the Boltzmann distribution arising from core temperature excursions and pump excited state absorption (ESA). In free-running systems, we show that inter-Stark level transitions that terminate on progressively higher Stark levels within the I-4(13/2) manifold in part describe the non-saturating behavior of the output power at moderate pump levels. The model was used to investigate the influence of dopant concentration, pump wavelength, pump configuration, output coupling and background loss of the fiber on laser performance. In contrast to a number of previous modeling investigations, our results show that the slope efficiency steadily increases with increasing erbium concentration as a result of the reduced rates of energy recycling caused by the weakly interacting Er3+ ions. The highest slope efficiency was obtained for a pump wavelength of 983 nm due to reduced levels of ESA, however, for both free-running and wavelength-fixed arrangements of the laser, pump ESA may ultimately preclude significant power scaling.

Numerical modeling of an ASE suppression and power scalable approach in 1908?nm LMA-TDFO

Theoretical Modelling of Cascaded Er3+-Doped, Tm3+-Doped and Nd3+-Doped Fibers for 0.4 to 2.0 Μm Emission Spectra

Suppressing the Amplified Spontaneous Emission in the High-Power 1018-Nm Monolithic Fiber Laser by Decreasing the Feedback from the Inner Reflections

Numerical Simulation Of 980 Nm-Ld-Pumped Yb3+-Er3+-Tm3+-Codoped Fiber Amplifier For 1500nm And 1600nm Bands

Numerical modeling of multi-point side-pumped mid-infrared erbium-doped fluoride fiber lasers

High repetition frequency tunability active Q-switched all-fiber laser by multi-gain sub-rings smoothing multipeak pulse and suppressing ASE self-saturation

Numerical Simulation of 980 nm-LD-Pumped Yb 3 +-Er 3 +-Tm 3 +-Codoped Fiber Amplifier for 1500 nm and 1600 nmBands

2 $μ$m Watt-level Fiber Amplifiers, Lasers, and ASE Sources Pumped by Broadband ASE Pumps

Numerical modeling of a high power terahertz source at Shanghai

933 W Yb-doped Fiber ASE Amplifier with 504 Nm Bandwidth

The Numerical Analysis of A Broadly Tunable Ytterbium-Doped Fiber Ring Laser

Parameters Optimization of ASE Source for the Improvement of Optical Power Stability in Space Radiation Environment

Modeling and Analysis of a Pulsed Yb-Tm Fiber Laser System

A 5 kW Nearly-Single-Mode Monolithic Fiber Laser Emitting at ~1050 nm Employing Asymmetric Bi-Tapered Ytterbium-Doped Fiber

Modeling and multidimensional optimization of a tapered free electron laser

Power Enhancement and Spot Homogenization Design for Arrayed Semiconductor Lasers

A 4.8-kW high-efficiency 1050-nm monolithic fiber laser amplifier employing a pump-sharing structure

Modeling and Optimization of Actively Q-switched 2.8 Μm Er3+-doped ZBLAN Fiber Laser

Numerical Modeling and Optimization of Diode Pumped Heavily-Erbium-Doped Fluoride Fiber Lasers

High-power and high-brightness Er:Yb codoped fiber MOPA operating at 1535 nm

High-power single-stage thulium-doped superfluorescent fiber source