Abstract:Al x CoCrFeNi (x = 0.1, 0.5 and 1) high-entropy alloys (HEAs) were prepared using a spark plasma sintering (SPS) technique combined with aerosol powder. Their microstructure and phase constituents were characterized using an X-ray diffractometer and SEM, and their tensile properties, hardness and compactness were tested. The results show that the crystal structure of the Al x CoCrFeNi HEAs changed significantly with the Al content, from the original single face-centered cubic FCC phase (Al0.1CoCrFeNi) to an FCC + BCC structure (Al0.5CoCrFeNi), and then to FCC + BCC + sigma (σ) phase structures (AlCoCrFeNi). Chemical composition analysis showed that the crystal structure transformation was related to the segregation caused by the increased Al content. The hardness of the Al x CoCrFeNi HEAs increases with increasing Al content, and the hardness of AlCoCrFeNi reaches a maximum of 507.3 HV. The tensile properties of the alloy show a trend of first increasing and then decreasing with increasing Al content, and the yield strength, ultimate tensile strength and elongation of the Al0.5CoCrFeNi alloy reach maximum values of 527.4 MP, 943.3 MPa and 28.2%, respectively. The fracture mechanism of the Al0.1CoCrFeNi and Al0.5CoCrFeNi alloys is typical ductile fracture, while that of the AlCoCrFeNi alloy is cleavage fracture. The compactness of the alloy increases with the Al content. The samples were also subjected to high-temperature water vapour corrosion, and corrosion products such as Al3Fe5O12, CoCr2O4 and NiCr2O4 were found in the Al0.1 and Al0.5 alloys, whereas no oxide peaks were detected using XRD for the Al1 alloy. It was also presumed that a very thin alumina film was generated on the surface of the Al1 alloy, preventing the oxidation of the sample, in combination with the analysis of SEM, EDS and XPS behaviour.

Synthesis and Characterization of WNiFeCo, WNiFeMo, and WNiFeCoMo Compositional Complex Alloys Manufactured by Powder Metallurgy Technique

Characterization of FeCoNiCr high-entropy alloys manufactured by powder metallurgy technique

Preparation and properties of FeNiMnCuC0.2Alx high-entropy alloy

Microstructures and mechanical properties of FeCoNi(MoW) high-entropy alloys

Effect of Mo Content on Microstructure and Mechanical Properties of CoCrFeNi Series High-entropy Alloys

Mechanical and tribological properties of (FeCoNi)88-x(AlTi)12Mox high-entropy alloys

Microstructure and mechanical properties of non equiatomic FeCoNiCuMo high entropy systems

Comparative study of the microstructure and phase evolution of FeCoCrNiAl high-entropy alloy-matrix WC nanocomposite powders prepared by mechanical alloying

Effect of Aluminum Addition on the Microstructure, Magnetic, and Mechanical Properties of FeCrCoNiMn High-Entropy Alloy

Effect of Tungsten on Microstructure and Mechanical Properties of Novel NiMnCrMoWx High-Entropy Alloys Developed by Mechanical Alloying

Microstructure and mechanical properties of Al-Fe-Co-Cr-Ni high entropy alloy fabricated via powder extrusion

Microstructure characterization and phase evolution of equiatomic AlCoMoFeNi high entropy alloy synthesized by mechanical alloying

Improving Mechanical Properties of Co-Cr-Fe-Ni High Entropy Alloy via C and Mo Microalloying

Microstructure and Properties of NiCoCrAlTi High Entropy Alloy Prepared Using MA-SPS Technique

Mechanical properties and water vapour corrosion behaviour of Al x CoCrFeNi high-entropy alloys

Mechanical properties and fracture mechanism of as-cast MnFeCoCuNi high-entropy alloys

Alloying behavior of W and Mo in the as-cast dual-phase FeNiCrAl multi-component alloys

The effect of Co substitutions for Ni on microstructure, mechanical properties and corrosion resistance of Fe50Mn25Cr15Ni10 medium-entropy alloy

Microstructure Evolution and Compressive Property Variation of CoCrFeNiAlx High Entropy Alloys Produced by Directional Solidification

A Study on the Phase Formation and Magnetic Properties of FeNiCoCuM (M = Mo, Nb) High-Entropy Alloys Processed Through Powder Metallurgy

Microstructure, Mechanical Properties, and Damping Capacity of AlxCoCrFeNi High-Entropy Alloys Prepared by Spark Plasma Sintering