Abstract:In this research, we are presenting a precise spectral adjustment procedure for light‐emitting diode (LED) and other multilight‐source solar simulators. Applying the procedure on an LED‐based solar simulator, we achieve excellent agreement in a measurement comparison conducted with Fraunhofer ISE CalLab, using a dual‐junction solar cell as test object. Solar simulators based on light‐emitting diodes (LEDs) usually consist of many spectrally different LEDs, which in sum produce a sun‐like spectrum. On the one hand, this results in the advantage of a high spectral tunability of these systems and on the other hand, however, also in the challenge of a high number of parameters which have to be set for the adjustment of a suitable simulator spectrum. Multijunction solar cells consisting of series‐connected subcells are very sensitive to spectral irradiance conditions, which are affecting the current and the fill factor of the device. A precise adjustment of the simulator spectrum based on the spectral responsivity of the subcells is therefore essential for accurate multijunction measurements. Therefore, the number of spectrally different light sources used should be at least as high as the number of subcells in the device under test. However, for the measurement of multijunction devices, the much higher number of spectrally different light sources in common LED solar simulators results in a plethora of different simulator spectra, potentially suitable for the measurement. Furthermore, the nonlinear intensity characteristics of the utilized LEDs as well as the distance‐dependent illumination uniformity of such solar simulators add complexity when aiming for a precise spectral adjustment. To tackle these challenges, a new spectral adjustment procedure which is based on a least square's solution algorithm and the definition of appropriate boundary conditions for the calculation of suitable simulator settings is introduced in this publication. Focusing on measurements carried out under constant illumination makes the presented method especially applicable for perovskite‐on‐silicon multijunction devices. Therefore, an adapted method for the determination of the solar simulator's spectral properties, considering thermal influences which are particularly relevant when carrying out continuous illumination measurements, is introduced in this work. The presented method is verified applying it on a Wavelabs SINUS 220 LED solar simulator by performing a measurement comparison on a multijunction solar cell with Fraunhofer ISE CalLab's well‐established multilight source solar simulator.

Measuring the device‐level EQE of multi‐junction photonic power converters

Accurate Optical Optimization of Light-Emitting Diodes with Consideration of Coupling Between Purcell Factor and Transmittance Coefficient

Improved grating monochromator set-up for EQE measurements of multi-junction solar cells

A novel method of determining bias lights for spectral response measurement of GaAs multi-junction laser power converters and its applications

A method to analyze current mismatch in a multijunction laser power converter based on I–V measurements

A Wavelength-Insensitive All-Silicon In-Line Optical Power Monitor for Multimode Silicon Photonics

Determining Ultra-low Absorption Coefficients of Organic Semiconductors from the Sub-bandgap Photovoltaic External Quantum Efficiency

A scanning device for spatial quantum efficiency measurements of photomultipliers tubes

Multiple tunnel diode peaks in I–V curves of a multijunction laser power converter

Unusual hot carrier effect and improved carrier extraction observed in asymmetric dilute-nitride quantum-engineered solar cells through photoluminescence (PL) and external quantum efficiency (EQE) measurements

Intensity-Modulated Photocurrent Spectroscopy Measurements of High-Efficiency Perovskite Solar Cells

Joint Evaluation of Internal Quantum Efficiency and Light Extraction Efficiency for AlGaN-based Deep Ultraviolet LEDs Considering Optical Polarization Properties

Measurement of Energy Distribution of Output Electrons From a Microchannel Plate Based on Vacuum Photodiode

Quick Spectrometric Characterization of Monolithic Perovskite Silicon Tandem Solar Cells Using Monochromatic Light Sources

Comparative Analysis of Excitonic and Biexcitonic Effects on the Power Conversion Efficiency of a CdSe/CdTe/ZnTe Quantum Dot Solar Cell

Power- and Spectral-Dependent Photon-Recycling Effects in a Double-Junction Gallium Arsenide Photodiode

Electrical derivative measurement of quantum cascade lasers (QCLs)

Measuring electrical properties in semiconductor devices by pixelated STEM and off-axis electron holography (or convergent beams vs. plane waves).

Perovskite Phase Analysis by SEM Facilitating Efficient Quasi‐2D Perovskite Light‐Emitting Device Designs

A precise method for the spectral adjustment of LED and multi‐light source solar simulators