Abstract:Selective laser melting (SLM) technology was employed for the additive manufacturing of Ti-5Al-2.5Sn alpha titanium alloy in this work and the influences of laser energy input on densification behavior, microstructure evolution and mechanical performances of the as-deposited products were investigated. It was found that the relatively high volumetric energy densities (VEDs) of 167-417 J/mm(3) resulted in large quantities of keyhole-induced spherical pores whereas the relatively low VEDs of 51-83 J/mm(3) led to notable lack-of-fusion defects. At the proper VED of 125 J/mm(3), highly densifled products with internal porosity of merely 0.05% were obtained. At the relatively high VEDs of 167-417 J/mm(3), as-built samples presented duplex microstructures composed of acicular alpha' martensites and bulk alpha(M) massive grains. In contrast, overwhelmingly martensitic microstructures were formed at lower VEDs of 51-125 J/mm(3). The martensitic microstructure exhibited a unique hierarchical feature, which could be explained using the theory of athermal martensitic transformation kinetics. With the decrease of VED from 417 J/mm(3), the average size of alpha' needles increased first, then came to its plateau at the VEDs of 167-208 J/mm(3), and decreased again at the VEDs of 51-167 J/mm(3). At the VEDs of 167-417 J/mm(3), the formation of spherical pores and bulk alpha(M) grains resulted in relatively poor tensile properties. At the VEDs of 51-83 J/mm(3), the formation of lack-of-fusion defects masked the enhanced fine-grain strengthening effect provided by the much refined alpha' needles and the decrease in the fraction of bulk alpha(M), thus also leading to very limited tensile properties. At the proper VED of 125 J/mm(3), as-built tensile properties reached to their peak with ultimate tensile strength of 1173 MPa, yield strength of 1061 MPa, and elongation of 7.7%. This can be attributed to the high densification degree, the almost complete vanish of bulk alpha(M) grains, and the moderate size of alpha' needles. (C) 2018 Elsevier B.V. All rights reserved.

In-situ nitrogen strengthening of selective laser melted Ti6Al4V with superior mechanical performance

Selective Laser Melting under the Reactive Atmosphere: A Convenient and Efficient Approach to Fabricate Ultrahigh Strength Commercially Pure Titanium Without Sacrificing Ductility

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

In-situ laser additive manufacturing of Ti6Al4V matrix composites by gas–liquid reaction in dilute nitrogen gas atmospheres

Microstructure and Mechanical Property Improvement of Laser Additive Manufacturing Ti–6Al–4V via the Niobium Addition

Outstanding strength-ductility balance in a Ti–N alloy by tuning ball milling time

Achieving grain refinement and ultrahigh yield strength in laser aided additive manufacturing of Ti−6Al−4V alloy by trace Ni addition

In-situ synthesis of high strength and toughness TiN/Ti6Al4V sandwich composites by laser powder bed fusion under a nitrogen-containing atmosphere

Additive Manufacturing of the High-Strength and Low Modulus Biomedical Ti-10 Nb Alloy under Reactive Atmosphere

Influence of Nitrogen on Microstructure, Mechanical Properties and Martensitic Phase Transformation of Co–26Cr–5Mo–5W Alloys by Selective Laser Melting

A titanium-nitrogen alloy with ultrahigh strength by ball milling and spark plasma sintering

Microstructure and Mechanical Properties of Ti6Al4V Alloy Prepared by Selective Laser Melting Combined with Precision Forging

Balanced Strength-Ductility Combination and Good Recoverable Strain of Ni50.7Ti49.3 Alloy Fabricated by High Scanning Velocity in Selective Laser Melting

Achieving high strength and ductility in selective laser melting Ti-6Al-4V alloy by laser shock peening

Strengthening layer with nano-twins in titanium alloy induced by laser surface re-melting: Mechanism of high strength and ductility

Strong and ductile titanium via additive manufacturing under a reactive atmosphere

Microstructure evolution and strengthening mechanisms of a high-performance TiN-reinforced Al-Mn-Mg-Sc-Zr alloy processed by laser powder bed fusion

Simultaneous Enhancement of Strength, Ductility, and Hardness of TiN/AlSi10Mg Nanocomposites Via Selective Laser Melting

Selective Laser Melting of Nano-Tib2 Decorated Alsi10mg Alloy with High Fracture Strength and Ductility

Comparative Study about the Properties of in Situ Synthesized TiN/Ti6Al4V Sandwich Structure Materials by Selective Laser Melting and Laser Directed Energy Deposition

Densification Behavior, Microstructure Evolution, and Mechanical Performances of Selective Laser Melted Ti-5Al-2.5Sn Α Titanium Alloy: Effect of Laser Energy Input