Abstract:A method of dispersion-strengthening tungsten, a refractory metal, with submicron (< 10 Å) dispersoids of hafnium nitride, a stable ceramic, is described. Simultaneous deposition of the metal and the dispersoid is achieved by a chemical vapor deposition process called covapor deposition. The tungsten and hafnium are covapor deposited by hydrogen reduction of their halides (WCl6 and HfCl4); the dispersoid is formed during deposition by the reaction of hafnium with NH3 in the hydrogen gas.The microstructure of the tungsten matrix, either the large columnar grains typical of chemical vapor deposited tungsten or fine noncolumnar grains (< 1 μm), can be controlled by varying the deposition parameters. It is also possible by varying these parameters to change the number, size, and spacing of the dispersoids.The deposits were heat treated at 1700 °C for at least 1 h before hot microhardness values to 1400 °C were determined. These values were then compared with hot microhardness values determined after heat treatment for 96 and 500 h at 1700 °C. The microstructures of the deposits in these conditions were evaluated by thin film and scanning electron microscope techniques. The hot microhardness of the LRL dispersion-strengthened tungsten was superior to that of dispersion-strengthened tungstens prepared by other techniques. The possibilities of using this technique to improve the strength and creep resistance of other metals (e.g., nickel-chromium alloys for turbine blades) is also suggested.Parameters are given for the deposition of pure tungsten and hafnium nitride from their halides.

Dispersion behavior of HfC‐based nanopowders in ethanol

Dispersion and co-dispersion of ZrB2 and SiC nanopowders in ethanol

Preparation and Dispersion Performance of Hydrophobic Fumed Silica Aqueous Dispersion

Study on Rheological Behavior of Micro/Nano-Silicon Carbide Particles in Ethanol by Selecting Efficient Dispersants

Dispersion behavior of silica fume in cementitious suspensions

A Powder Metallurgy Route to Fabricate CNT-reinforced Molybdenum-Hafnium-carbon Composites

Carbon-bonded Carbon Fiber Composites Containing Uniformly Distributed Silicon Carbide

Si-HfO2 composite powders fabricated by freeze drying for bond layer of environmental barrier coatings

Dispersion Properties of Molecular Sieve Slurry in Preparation of Fluidized Catalytic Cracking Catalyst

Preparation of (Ti0.2Zr0.2Hf0.2Nb0.2Ta0.2)C high‐entropy ceramic nanopowders via liquid‐phase precursor

Dispersion Behavior of SiC Micro Whiskers in Aqueous Medium

Influence of Polyelectrolyte Dispersant on Slip Preparation of Nano-Sized Tetragonal Polycrystals Zirconia for Aqueous-Gel-tape-casting Process

Effect of Dispersants on the Rheological Properties and Slip Casting of Concentrated Alumina Slurry

Enhanced Sedimentation Stability of Carbonyl Iron Powders with Hydrophilic Siloxane Polymer Coatings in Ethanol

Homogeneous nanoparticle dispersion prepared with impurity-free dispersant by the ball mill technique

Influence of Silane Coupling Agent and Anionic Dispersant on the Dispersion Effect of Silicon Carbide Particles

Efficient Composite Dispersants for High Solid Content, Low Viscosity Nano-Zirconia Slurries: An Experimental and Molecular Dynamics Simulation Study

Low-temperature Rapid Synthesis of Ultrafine Hafnium Carbide Ceramic Powders

Fabrication of ultra-fine grained Hf-based materials with superior hardness and temperature-independent electrical conductivity by a combination of high-energy ball milling and spark plasma sintering

Microstructure and ablation resistance of C/C-HfC-SiC composites prepared by RMI with different powder particle sizes

Ultrafine dispersion-strengthening of tungsten by chemical covapor deposition