Abstract:The setting time of the paste and the rheological properties and microstructure of the mortar after replacing OPC cement with silica fume (SF), fly ash cenosphere (FAC) and nano-silica are studied as a reference for shotcrete applications. The suggested contents of SF, FAC and nano-silica are around 5–7.5%, higher than 20% and 1–3%, respectively, to meet the initial setting time specification. Viscosity and yield stress of mortar are highly dependent on water/cement ratio and paste/sand ratio. At the higher water/cement ratio, viscosity is more based on the paste itself. For SF of 2.5–10%, viscosity and yield stress increase, and the flowability of the mixture decreases. For FAC of 5–25%, viscosity and yield stress increase with a lower rate than SF, and flowability increases at 5% and then decreases as FAC content increases, which, however, is at the same level as the control. When SF and FAC are both added, a tortuous behavior of viscosity is shown. As nano-silica is further added, significant increases in viscosity and yield stress are shown. The compressive strengths of mortar with different supplementary cementitious materials (SCMs) at early ages are close. The difference in compressive strength after 28 days of standard curing is significant. The SF5-FAC15 group exhibits the largest increase in strength for 32.82%. At the age of 2.5 h, the macropore areas distribution of SF5-FAC25-NS1.5 test groups were 31.96%, indicating the lowest macropore area distribution. The secondary hydration reaction of supplementary cementitious materials (SCMs) continuously generates products that fill the pores, and the ultrafine filling effect of nanomaterials improves the compactness of the mortar microstructure and reduces the macropore area distribution. The mercury intrusion test results of the SF5-FAC25-NS1.5 group show that the pores are concentrated within the range of 0.01 to 0.05 μm, and the most probable pore size is significantly smaller than that of the CTR group. As the overall replacement level of SCMs increases, the diffraction peak of calcium hydroxide gradually weakens.

Dispersion behavior of silica fume in cementitious suspensions

Comparative Study of Effect of Raw and Densified Silica Fume in the Paste, Mortar and Concrete

Effect of silica fume-enhanced carbon nanotube dispersion on the strength and damping properties of cement composites

The Dispersion and Hydration Improvement of Silica Fume in UHPC by Carboxylic Agents

Effect of silica fume on rheology of slag-fly ash-silica fume-based geopolymer pastes with different activators

Preparation and Dispersion Performance of Hydrophobic Fumed Silica Aqueous Dispersion

Analysis of the Damping Behavior and Microstructure of Cement Matrix with Silane-Treated Silica Fume

Influence of silica fume on the workability and hydration process of ultra-high performance concrete

Study on the Influence of Silica Fume (SF) on the Rheology, Fluidity, Stability, Time-Varying Characteristics, and Mechanism of Cement Paste

Rheology of Fumed Silica/Polydimethylsiloxane Suspensions

Influence of Silica Flour–silica Fume Combination on the Properties of High Performance Cementitious Mixtures at Ambient Temperature Curing

Effect of Silica Fume on the Rheological Properties of Cement Paste with Ultra-Low Water Binder Ratio

Effect of densified silica fume on low workability concrete strength development process

Rheological Properties of Composite Binder Paste Containing Different Types of Silica Fume

Effect of Adding Solid Waste Silica Fume As a Cement Paste Replacement on the Properties of Fresh and Hardened Concrete

Influence of nano-silica agglomeration on microstructure and properties of the hardened cement-based materials

Rheological behaviour, setting time, compressive strength and microstructure of mortar incorporating supplementary cementitious materials and nano-silica

Hydration and Mechanical Properties of High-Volume Fly Ash Concrete with Nano-Silica and Silica Fume

Uncovering the role of hydrophobic silica fume (HPS) in rheology, hydration, and microstructure of ultra-high-performance concrete (UHPC)

Effect of Silica Fume Utilization on Structural Build-Up, Mechanical and Dimensional Stability Performance of Fiber-Reinforced 3D Printable Concrete

Research on Cement Slurry Using Silica Fume Instead of Fly Ash