Abstract:Flexible capacitive tactile sensors show great promise in personalized healthcare monitoring and human-machine interfaces, but their practical application is normally hindered because they rarely possess the required comprehensive performance, that is, high pressure sensitivity and fast response within a broad pressure range, high structure robustness, performance consistency, etc. This paper aims to engineer flexible capacitive pressure sensors with highly ordered porous dielectric microstructures and a 3D-printing-based fully solution-processable fabrication process. The proposed dielectric layer with uniformly distributed interior microporous can not only increase its compressibility and dynamic response within an extended pressure range but also enlarge its contact area with electrodes, contributing to a simultaneous improvement in the sensitivity, response speed, detection range, and structure robustness. Meanwhile, owing to its superior abilities in complex structure manufacturing and dimension controlling, the proposed 3D-printing-based fabrication process enables the consistent fabrication of the porous microstructure and thus guarantees device consistency. As a result, the prepared pressure sensors exhibit a high sensitivity of 0.21 kPa-1, fast response and relaxation times of 112 and 152 ms, an interface bonding strength of more than 455.2 kPa, and excellent performance consistency (≤5.47% deviation among different batches of sensors) and tunability. Encouraged by this, the pressure sensor is further integrated with a wireless readout circuit and realizes wireless wearable monitoring of various biosignals (pulse waves and heart rate) and body movements (from slight finger touch to large knee bending). Finally, the influence law of the feature parameters of the porous microstructure on device performance is established by the finite element method, paving the way for sensor optimization. This study motivates the development of flexible capacitive pressure sensors toward practical application.

Printed Composite Film with Microporous/Micropyramid Hybrid Conductive Architecture for Multifunctional Flexible Force Sensors

Microfluidic Channel-Based Soft Electrodes and Their Application in Capacitive Pressure Sensing

Deep Eutectic Solvent Induced Porous Conductive Composite for Fully Printed Piezoresistive Pressure Sensor

A Polyimide Based Force Sensor Fabricated Using Additive Screen-Printing Process for Flexible Electronics

Flexible capacitive pressure sensor based on electrically assisted micro-nanoimprinting

Novel Flexible Force Sensor Based On Carbon Composites

Study Of A Novel Flexible Force-Sensitive Carbon Composite Film

Molding-Free Fully-Printed Flexible Tactile Sensors with Performance- Enhancing Microstructures

Design and Fabrication of Flexible Capacitive Sensor With Cellular Structured Dielectric Layer via 3D Printing

Flexible Force Sensor with Micro-Pyramid Arrays Based on 3D Printing

Flexible Pressure Sensor with Micro-Structure Arrays Based on PDMS and PEDOT:PSS/PUD&CNTs Composite Film with 3D Printing

Sensitive, Robust, Wide-Range, and High-Consistency Capacitive Tactile Sensors with Ordered Porous Dielectric Microstructures

Multimodal Electrohydrodynamic Jet Printing-Based Microstructure-Sensitized Flexible Pressure Sensor

Micro Structuring Polydimethylsiloxane Elastomer Film with 3D Printed Mold for Low Cost and High Sensitivity Flexible Capacitive Pressure Sensor

The Design and Numerical Simulation of a 3D-Printed Flexible Capacitive Pressure Sensor with a Composite Structure

High-Performance Flexible Piezoresistive Pressure Sensor Printed with 3D Microstructures

Biosustainable Multiscale Transparent Nanocomposite Films for Sensitive Pressure and Humidity Sensors

Advancing pressure sensors performance through a flexible MXene embedded interlocking structure in a microlens array

Flexible Pressure Sensor With High Sensitivity and Fast Response Based on Bionic Honeycomb-Structured Polydimethylsiloxane/Aluminum Oxide Composites Dielectric via 3-D Printing

Facile Fabrication of Highly Sensitive Thermoplastic Polyurethane Sensors with Surface- and Interface-Impregnated 3D Conductive Networks

Highly Sensitive, Ultrawide Range, and Multimodal Flexible Pressure Sensor with Hierarchical Microstructure Prepared By a One‐Step Laser Printing Process