Abstract:Ternary blends have been considered as an effective approach to improve power conversion efficiency (PCE) of organic solar cells (OSCs). Among them, the fullerene-containing ternary OSCs have been studied extensively, and their PCEs are as high as over 14%. However, all non-fullerene acceptor ternary OSCs are still limited by their relatively lower PCEs. In this work, we used wide-bandgap benzodithiophene-difluorobenzotriazole copolymer FTAZ as the donor, low-bandgap fused-ring electron acceptor (FREA), fused tris(thieno-thiophene) end-capped by fluorinated 1,1-dicyanomethylene-3-indanone (FOIC) as acceptor, and two medium-bandgap FREAs, indaceno-dithiophene end capped by 1,1-dicyanomethylene-3-indanone (IDT-IC) and indacenodithiophene end-capped by 1,1-dicyanomethylene-3-benzoindanone (IDT-NC), as the third components to fabricate the ternary blends FTAZ:FOIC:IDT-IC and FTAZ:FOIC:IDT-NC, and investigated the effects of the third components on the performance of ternary OSCs. Both IDT-IC and IDT-NC are based on the same indacenodithiophene core but contain different terminal groups (phenyl and naphthyl). Relative to IDT-IC with phenyl terminal groups, IDT-NC with naphthyl terminal groups has extended pi-conjugation, down-shifted lowest unoccupied molecular orbital (LUMO), red-shifted absorption and higher electron mobility. The binary devices based on the FTAZ:FOIC, FTAZ:IDT-IC and FTAZ:IDT-NC blends exhibit PCEs of 9.73%, 7.48% and 7.68%, respectively. Compared with corresponding binary devices, both ternary devices based on FTAZ:FOIC:IDT-IC and FTAZ:FOIC:IDT-NC exhibit better photovoltaic performances. When the IDT-IC weight ratio in acceptors is 50%, the FTAZ:FOIC:IDT-IC ternary devices exhibit the best PCE of 11.2%. The ternary-blend OSCs yield simultaneously improved open-circuit voltage (V-OC), short-circuit current density (J(SC)) and fill factor (FF) compared with the binary devices based on FTAZ:FOIC. The higher V-OC is attributed to the higher LUMO energy level of IDT-IC compared with FOIC. The improved J(SC) is attributed to the complementary absorption of FOIC and IDT-IC. The introduction of IDT-IC improves blend morphology and charge transport, leading to higher FF. The FTAZ:FOIC:IDT-NC system yields a higher PCE of 10.4% relative to the binary devices based on FTAZ:FOIC as the active layer. However, the PCE of the FTAZ:FOIC:IDT-NC-based ternary devices is lower than that of the FTAZ:FOIC:IDT-IC-based ternary devices. Compared with the binary devices based on FTAZ:FOIC, in FTAZ:FOIC:IDT-NC-based ternary devices, as the ratio of the third component increases, the V-OC increases due to the higher LUMO energy level of IDT-NC, the FF increases due to optimized morphology and improved charge transport, while the J(SC) decreases due to the overlapped absorption of FOIC and IDT-NC. The terminal groups in the third components affect the performance of the ternary OSCs. The lower LUMO. energy level of IDT-NC is responsible for the lower V-OC of the FTAZ:FOIC:IDT-NC devices. The red-shifted absorption of IDT-NC leads to the overlapping of the absorption spectra of IDT-NC and FOIC and lower J(SC). On the other hand, replacing the phenyl terminal groups by the naphthyl terminal groups influences the rr-rr packing and charge transport. The FTAZ:FOIC:IDT-NC blend exhibits higher electron mobility and more balanced charge transport than FTAZ:FOIC:IDT-IC, leading to a higher FF.

Effects of Side Chains in Third Components on the Performance of Fused-Ring Electron-Acceptor-Based Ternary Organic Solar Cells

A Comprehensively Theoretical and Experimental Study of Carrier Generation and Transport for Achieving High Performance Ternary Blend Organic Solar Cells

Effects of Terminal Groups in Third Components on Performance of Organic Solar Cells

Adding a Third Component with Reduced Miscibility and Higher LUMO Level Enables Efficient Ternary Organic Solar Cells

High Efficiency Ternary Organic Solar Cells Via Morphology Regulation with Asymmetric Nonfused Ring Electron Acceptor

Enhancing Performance of Non-Fullerene Organic Solar Cells Via Side Chain Engineering of Fused-Ring Electron Acceptors

Achieved 18.9% Efficiency by Fine‐Tuning Non‐Fullerene Acceptor Content to Simultaneously Increase the Short‐Circuit Current and Fill Factor of Organic Solar Cells

Enhanced short circuit current density and efficiency of ternary organic solar cells by addition of a simple copolymer third component

Ternary Organic Solar Cells with Efficiency >16.5% Based on Two Compatible Nonfullerene Acceptors.

Combining Fused‐Ring and Unfused‐Core Electron Acceptors Enables Efficient Ternary Organic Solar Cells with Enhanced Fill Factor and Broad Compositional Tolerance

Enhancing the performances of all-small-molecule ternary organic solar cells via achieving optimized morphology and 3D charge pathways

High-Performance PM6:Y6-Based Ternary Solar Cells with Enhanced Open Circuit Voltage and Balanced Mobilities Via Doping a Wide-Band-Gap Amorphous Acceptor.

A Near-Infrared Photoactive Morphology Modifier Leads to Significant Current Improvement and Energy Loss Mitigation for Ternary Organic Solar Cells

Exploiting Mechanism of Enhanced Charge Transfer in Ternary Organic Solar Cells at Low Energy Loss

High‐Efficiency Binary and Ternary Organic Solar Cells Based on Novel Nonfused‐Ring Electron Acceptors

Promoting charge separation resulting in ternary organic solar cells efficiency over 17.5%

Fine-tuning of film morphology through addition of a third component enables organic solar cells with efficiency over 18%

Over 16.5% efficiency in ternary organic solar cells by adding an alloyed acceptor with energy transfer process

Understanding the Impact of Hierarchical Nanostructure in Ternary Organic Solar Cells

Efficient Ternary Organic Solar Cells with Small Aggregation Phases and Low Bimolecular Recombination Using ICBA: ITIC Double Electron Acceptors

High‐Efficiency Ternary Organic Solar Cells Based on the Synergized Polymeric and Small‐Molecule Donors