Abstract:In this article, ternary organic solar cells (T‐OSCs) are fabricated under open‐air conditions. The optimized ternary device with 20% DRCTF shows power conversion efficiency of 14.45% with enhanced short‐circuit current density, open‐circuit voltage, fill factor, and reduced non‐radiative ΔVloss. This efficiency is higher than binary counterpart (12.46%). The design approach can serve as a foundation for future T‐OSC advancements. The structural disorder and aggregation of the third acceptor with the host active layer are critical in the light absorption, film morphology, and charge‐carrier mechanism of their photovoltaic blends to achieve highly efficient organic solar cells (OSCs). However, an effective third component needs to be introduced in the host binary blend as a combination of ternary blend, which can improve the absorption profile, film morphology, and charge dynamics. In this work, non‐fullerene acceptor DRCTF is incorporated as a third component in host PM6:Y6 binary blend. Compared to host blend, the ternary blend improves charge‐transfer processes, as evidenced by steady‐state photoluminescence and time‐resolved photoluminescence measurements. It is found that the addition of 20% DRCTF into host binary blend results in improved charge dissociation and transport with reduced recombination, and voltage losses. All these characteristics contribute to an improved power conversion efficiency of 14.45% in the PM6:Y6:DRCTF ternary OSCs (T‐OSCs), compared to PM6:Y6 (12.46%) in open‐air fabrication conditions. Consequently, in this study, the impact of third components on the charge‐transfer mechanism in T‐OSCs is elucidated. These findings suggested that T‐OSCs with a perfectly chosen third component in the host binary blend achieve a comprehensive absorption profile, smooth film morphology, efficient charge dynamics, and reduced voltage loss.

Fine-tuning of film morphology through addition of a third component enables organic solar cells with efficiency over 18%

Enhanced short circuit current density and efficiency of ternary organic solar cells by addition of a simple copolymer third component

Ternary Organic Solar Cells with Efficiency >16.5% Based on Two Compatible Nonfullerene Acceptors.

Boosting Photovoltaic Performance of Ternary Organic Solar Cells by Integrating a Multi-Functional Guest Acceptor

Non-fullerene acceptor fibrils enable efficient ternary organic solar cells with 16.6% efficiency

A Near-Infrared Photoactive Morphology Modifier Leads to Significant Current Improvement and Energy Loss Mitigation for Ternary Organic Solar Cells

Achieved 18.9% Efficiency by Fine‐Tuning Non‐Fullerene Acceptor Content to Simultaneously Increase the Short‐Circuit Current and Fill Factor of Organic Solar Cells

Achieving high-performance ternary organic solar cells by adding a high hole-mobility non-fullerene acceptor

Highly Efficient Ternary Solar Cells with Efficient Förster Resonance Energy Transfer for Simultaneously Enhanced Photovoltaic Parameters

Promoting charge separation resulting in ternary organic solar cells efficiency over 17.5%

Ternary Organic Solar Cells by Small Amount of Efficient Light Absorption Polymer PSEHTT as Third Component Materials

Exploiting Mechanism of Enhanced Charge Transfer in Ternary Organic Solar Cells at Low Energy Loss

Third component with a high LUMO energy level enables 17.69% efficiency in ternary organic solar cells

Efficient Ternary Organic Solar Cells Enabled by the Integration of Nonfullerene and Fullerene Acceptors with a Broad Composition Tolerance

Enhancing Intermolecular Packing and Light Harvesting through Asymmetric Non-Fullerene Acceptors for Achieving 18.7% Efficiency Ternary Organic Solar Cells

Small Molecule Ternary Solar Cell with Two Synergistic Electron Acceptors for Enhanced Photovoltaic Performance

Ternary Strategy Enabling High‐Performance Organic Solar Cells with Optimized Film Morphology and Reduced Nonradiative Energy Loss

Achieving 19.72% Efficiency in Ternary Organic Solar Cells through Electrostatic Potential‐Driven Morphology Control

Adding a Third Component with Reduced Miscibility and Higher LUMO Level Enables Efficient Ternary Organic Solar Cells

A simple-structured benzo[1,2-b:4,5-b']dithiophene-based molecule as a third component enables organic solar cells with over 18.2% efficiency

Oligomer-Assisted Photoactive Layers Enable >18 % Efficiency of Organic Solar Cells