Abstract:Longitudinal-torsional ultrasonic vibration-assisted milling is a machining method that can effectively improve the quality of the machined surface. When this method is used for the end milling of TC18 titanium alloy, however, the law of influence on the machined surface and subsurface remains unclear. In this study, we examined the effects of the ultrasonic amplitude, feed rate, and cutting speed on the machined surface morphology, roughness, surface residual stress, and subsurface microstructure in the longitudinal-torsional ultrasonic vibration-assisted end-milling process. According to the results, longitudinal-torsional ultrasonic vibration-assisted end milling can help form more obvious surface microtextures with a more distinct surface texture regularity at large amplitude, small feed rate, and high cutting speed. Compared with conventional milling, longitudinal-torsional ultrasonic vibration-assisted milling generates a larger roughness and surface residual stress and a deeper plastic deformation layer of the subsurface in the case of an obvious highly perturbed layer. In addition, the surface residual stress becomes greater and the plastic deformation layer gets deeper at a larger amplitude. When the amplitude was 5 μm, the surface residual stress was − 450.625 MPa and the depth of the deformation layer was 5.4 μm. The stress and depth increased by 21.55 % and 134.78 %, respectively, compared with those of conventional milling. The increase in the feed rate enhanced the roughness, decreased the surface residual stress, and did not significantly alter the depth of the plastic deformation layer. When the feed rate was 0.01 mm/z, the roughness was 0.383 μm and the surface residual stress was − 479.1 MPa. The feed rate and roughness increased by 42.63 % and 20.62 %, respectively, compared with those of conventional milling. With the increase in the cutting speed, the roughness increased, and the surface residual stress and the depth of the plastic deformation layer decreased. When the cutting speed was 15 m/min, the roughness was 0.31 μm, the surface residual stress value was − 454.7 MPa, and the depth of the plastic deformation layer was 5.7 μm. These three parameters increased by 17.8 %, 18.79 %, and 92.5 %, respectively, compared with those of conventional milling. This research has certain application prospect in surface machining of titanium alloy and quality control of machined surface.

Generation mechanism of high-order waves in wide titanium strip under the control of the first intermediate taper roll of a 20-high mill

Research on the generation and control of high-order flatness during the controlling of titanium strip profile by the intermediate taper roll in a 20-high mill

Numerical and experimental analysis of edge wave defect control during TA2 circular tube cold roll forming

Numerical and experimental analysis of defects control in cross wedge rolling for titanium alloy workpieces

Precise local deformation control for UHSS thin-walled component in roll forming

Study on quarter-wave generation mechanism in DP980 steel during cold rolling

Numerical Analysis on Flatness Adjusting Performance of Hot Wide Strip Temper Mill with Small-Diameter Work Rolls

Research on quarter-wave control in DP980 steel during cold rolling based on multi-pass simulation

Design of intermediate roll contour and analysis of regulation ability on strip shape of 18-High mill

Elongation Control of the Ultra-Thin Tinplate During Two-Stand Temper Rolling Unsteady Process

Research on roll contour and control strategy for edge drop control of high-strength steel in the cold rolling precision mill

Research on variable crown work roll curve design for W-shaped profile control of strips

Study on quarter-wave control of DP980 steel based on a bending force linear combination strategy

Symmetrical Variable Taper Plus: a novel variable crown work roll technology for enhancing edge drop control of hot-rolled strips

Mathematical and numerical analysis of cross-directional control for SmartCrown rolls in strip mill

Multi-roll Levelling for Wave Defects of Metal Sheets Based on the Beam-Membrane Method

Numerical and experimental study of the taper-rolling process for producing a helical blade from a metal strip

Numerical analysis of the strip crown inheritance in tandem cold rolling by a novel 3D multi-stand FE model

Influence of the rotational speed ratio of rollers on the three-dimensional surface rolling process

Surface and subsurface analysis of TC18 titanium alloy subject to longitudinal-torsional ultrasonic vibration-assisted end milling

Modelling of axial thrust force between rolls in strip mill