Abstract:Three-dimensional (3D) ferroelectric materials are electromechanical building blocks for achieving human–machine interfacing, energy sustainability, and enhanced therapeutics. However, current natural or synthetic materials cannot offer both a high piezoelectric response and desired mechanical toughness at the same time to meet the practicality. Here, a lamellar ferroelectric metamaterial was created with a ceramic-like piezoelectric property and a bone-like fracture toughness through a low-voltage-assisted 3D printing technology. The one-step printed bulk structure, consisting of periodically intercalated soft ferroelectric and hard electrode layers, exhibited a significantly enhanced longitudinal piezoelectric charge coefficient (d33) of over 150 pC N–1, as well as a superior fracture resistance of ∼5.5 MPa·m1/2, more than three times higher than conventional piezo-ceramics. The excellent printability together with the combination of both high piezoelectric and mechanical behaviors allowed us to create a bone-like structure with tunable anisotropic piezoelectricity and bone-comparable mechanical properties, showing a potential of manufacturing practical, high-performance, and smart biological systems.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsnano.1c05003.Discussions of crystallinity calculation of printed PVDF-HFP and PVDF, structural influence on metamaterials piezoelectricity, in-series model printing, adhesion energy calculation, fracture toughness calculation, and mechanism behind toughness enhancement, figures of PVDF and PVDF-HFP printing and properties comparison, characterization of Li-KNN materials, electrical conductivity measurement of the electrode layer, ferroelectric mematerial interface investigation, fabrication and properties of PVDF-HFP/Li-KNN printing raw material, piezoelectric property of a single ferroelectric layer, insitu poling electric potential design, two different printing processes of the multilayered structure, mechanical moduli of PLA/CB and PVDF-HFP/Li-KNN films, mechanical stimuli and short circuit current, open circuit voltage measured from metamaterials, piezoelectricity of 25-ferro-layered metamaterial, direct printing in situ poled ferroelectric material with in-series connection of all ferroelectric layers, interfacial adhesion characterization of printed bilayer structures, PLA/CB peeling surface observation, toughness enhancement and mechanism, mechanical modulus tuning, influence of porosity on piezoelectricity, and table of estimated equivalent dielectric constants εr and piezoelectric voltage constants g33 of printed structures (PDF)Video of extrusion of ferroelectric composite by a customized extruder system (MOV)Video of current output of three-unit ferroelectric structure under 100 N mechanical stimuli (MOV)Video of current output of seven-unit ferroelectric structure under the same mechanical stimuli (MOV)Video of lighting 10 LED bulbs by 3D-printed bulk ferroelectric structure (MOV)Video of low-voltage-assisted printing of 25-unit scaled ferroelectric structure (MOV)This article has not yet been cited by other publications.

Bulk Ferroelectric Metamaterial with Enhanced Piezoelectric and Biomimetic Mechanical Properties from Additive Manufacturing

Development of Mechanically Enhanced Polycaprolactone Composites by a Functionalized Titanate Nanofiller for Melt Electrowriting in 3D Printing.

A 3D-printed molecular ferroelectric metamaterial

Polyvinylidene Fluoride Energy Harvester with Boosting Piezoelectric Performance through 3D Printed Biomimetic Bone Structures

Polar and toroidal electromechanical properties designed by ferroelectric nano-metamaterials

A Novel Microwave Assisted Multi-Material 3D Printing Strategy to Architect Lamellar Piezoelectric Generators for Intelligent Sensing

Multi-material 3D printing of piezoelectric and triboelectric integrated nanogenerators with voxel structure

Lead-Free Piezoelectric Composite Based on a Metamaterial for Electromechanical Energy Conversion

Printable Multi-Stage Variable Stiffness Material Enabled by Low Melting Point Particles Additives

3D printing of PVDF-based piezoelectric nanogenerator from programmable metamaterial design: Promising strategy for flexible electronic skin

Observation of Ferroelectric Programmability in 3D Printed Metamaterials

Functional Additive Manufacturing of Large-size Metastructure with Efficient Electromagnetic Absorption and Mechanical Adaptation

3D Printing of Flexible Mechanical Metamaterials: Synergistic Design of Process and Geometric Parameters

Boosting Piezoelectricity by 3D Printing PVDF‐MoS2 Composite as a Conformal and High‐Sensitivity Piezoelectric Sensor

Additive Manufacturing of Ferroelectric-Oxide Thin-Film Multilayer Devices

Mechanical behavior analyses of 4D printed metamaterials structures with excellent energy absorption ability

Direct 3D Printing of Piezoelectrets: Process Feasibility, Prototypes Fabrication and Device Performance

Superior compressive properties of 3D printed plate lattice mechanical metamaterials

Study on the control of mechanical and electrical properties of 3d printed BTO/PDMS flexible porous composites

4D Printing of customizable and reconfigurable mechanical metamaterials

Porous, Self-Polarized Ferroelectric Polymer Films Exhibiting Behavior Reminiscent of Morphotropic Phase Boundary Induced by Size-Dependent Interface Effect for Self-Powered Sensing