Abstract:Titanium dioxide (TiO 2 ), as an n-type semiconductor photocatalyst, has been widely studied and used in many environmental and energy applications such as solar cells, wastewater treatment, air purification, water splitting for hydrogen production and CO 2 conversion due to its superior electrical and optical properties, stability, and biocompatibility. Using its photocatalytic and other properties, we have been studying a floating photoelectrochemical cell that can be applicable to the marine environments. This cell is designed to utilize titanium dioxide as its photoanode and copper oxides photocathode, and seawater is used as an electrolyte between electrodes. The drawbacks of using titanium dioxide as photocatalysts are its high electron-holes recombination rates and lower absorption efficiency in visible light regions. To improve against these drawbacks, we studied hydroxyapatite (HAp, Ca 10 (PO 4 ) 6 (OH) 2 ) as co-catalyst for titanium dioxide electrode. Since HAp possesses biocompatibility, it is suitable to be used with TiO 2 electrode in marine environments. In previous studies, it was found that HAp improved and boosted the current density produced by the titanium dioxide electrode. However, removal of HAp occurred from the surface of titanium dioxide during the photoelectrochemical measurements. Therefore, in this study, we have optimized the content of HAp paste that would be applied to the surface of titanium dioxide electrode by screen printing method. For preparation of titanium dioxide electrode, type 329J4L stainless steel was selected as the base substrate. Firstly, surface of the substrate was grinded to form the grid pattern and cleaned with ethanol in ultrasonic cleaner and then with distilled water. After that, the substrate was passivated with 10 % HNO 3 at 60 oC for 30 minutes. The passivated substrate was then printed and heat treated with TiO 2 paste twice at 150 oC for 1 hour and 550 oC for 30 minutes respectively. Double layered titanium dioxide electrode was then printed with HAp paste and heat treated at 150 oC for 1 hour. To check the characteristics of photocatalytic effect of electrode, photopotential and potentiodynamic polarization measurements were performed to the electrode. For illumination test, xenon light with an intensity of 10.5 mW/cm 2 and a calibrated wavelength of 250-800 nm was used as the light source. The measurement was conducted in artificial seawater as the controlled electrolyte. Standard calomel electrode (SCE) was used as a reference electrode and platinum electrode as a counter electrode. The measurement was performed both with and without irradiated conditions. The microstructures and surface morphology of electrode before and after electrochemical measurements were analyzed and examined by scanning electron microscope (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction analysis (XRD). The results show optimized HAp also improve the photocatalytic activities of n-type semiconductor titanium dioxide. In previous study, removal of HAp was considered due to the addition of carboxymethyl cellulose (CMC) as a viscosity modifier to HAp paste. CMC possess higher hydration rate which may cause rapid agglomeration when it is introduced to water. Although it has satisfactory quality to control the viscosity of the paste, rapid hydration cause removal of HAp after the electrode was heat treated and measurement was performed in artificial seawater. In this study, polyethylene glycol (PEG) was used as the viscosity modifier for HAp paste and Triton-X-100 was used as the surfactant to control the surface tension of the paste. As a result, HAp paste was produced to be screen-printable onto the surface of TiO 2 electrode and removal of HAp was minimized compared to the previous study. Moreover, HAp became a good sorbent and co-catalyst for titanium dioxide electrode in its photocatalytic activities.

Ti-Modified Hydroxyapatites: Synthesis, Crystal Chemistry, and Photocatalytic Activity

Effect of Supersaturation on the Morphology of Hydroxyapatite Crystals Deposited by Electrochemical Deposition on Titanium

Improvement of Bioactivity of H(2)O(2)/TaCl(5)-treated Titanium after Subsequent Heat Treatments.

Controllable Hydrothermal Synthesis, Optical and Photocatalytic Properties of TiO2 Nanostructures

Preparation and characterization of a titanium-substituted hydroxyapatite photocatalyst

Room‐Temperature Hydrolysis of Potassium Titanyl Oxalate and Water‐Assisted Crystallization for TiO2 with High Photocatalytic Activity

Preparation of Nanocrystals Hydroxyapatite/tio2 Compound by Hydrothermal Treatment

Hydrothermal synthesis and photocatalytic property of CaTiO 3 assisted with sodium citrate

(001)-Exposed TiO2 Microcrystals Decorated with Few-Layer Nanobelts for Enhanced Photocatalytic Activity

Hydrothermal Synthesis and Photocatalytic Property of CaTiO_3 Assisted with Sodium Citrate

Effect of Calcination Temperature on Crystal Structure and Photocatalytic Prop- Erty of TiO2/Diatomite Nanoparticles

Different solvents and organic modifiers for the controlling of crystallographic parameters in nano-crystallite hydroxyapatite for amplification of photocatalytic activity

The Effect of Heat-Treatment and Bioresorbability of Silicate-Containing Hydroxyapatite

Synthesis of Titanium Oxide Nanotubes Loaded with Hydroxyapatite

Analysis of Photocatalytic Properties of Titanium Dioxide Electrode Supported By Hydroxyapatite Co-Catalyst in a Marine Solar Cell

Influence of titanium ion doping on structural changes in porous hydroxyapatite ceramics

Calcined Hydroxyapatite Powders with Increased Chemical Stabilities and Dispersibility

Photocatalytic Degradation of Bisphenol A Using Ti-substituted Hydroxyapatite

Synthesis of Hydroxyapatite Coatings with Hexagonal Crystal Structure on Etched Titanium by Hydrothermal Method

Hydrothermal Calcification of Alkali Treated Titanium in CaHPO4 Solution

Hydrophilicity of Bioactive Titanium Surface with Different Structure, Composition, Crystal Form and Grain Size