Abstract:Despite the rapid progress that has been made in increasing the power conversion efficiency (PCE) of organic solar cells (OSCs) over the past decade, it is a challenge to realize efficient and environment-friendly OSCs. In this contribution, all polymer solar cells were fabricated with a blend of poly[4,8-bis(5-(2-ethylhexyl) thiophen-2-yl) benzo[1,2-b: 4,5-b'] dithiophene-co-3-fluorothieno[3,4-b] thiophene-2-carboxylate] (PTB7Th) donor and vinylene-bridged perylenediimide-based polymer (PDI-V) acceptor, in which non-halogenated tetrahydrofuran (THF) was used as the host solvent. A conventional device structure of ITO/poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS)/PTB7-Th:PDI-V/zirconium acetylacetonate (ZrAcac)/Al was employed, where PEDOT:PSS functioned as the hole transporting layer (HTL) and ZrAcac functioned as the electron transporting layer (ETL). The mixed solution of PTB7-Th and PDI-V was spin cast on the top of PEDOT:PSS layer to form the active layer. After that, ZrAcac solution was spin cast on the top of PTB7-Th:PDI-V layer. Different thermal annealing temperatures were used to optimize the active layer morphology. In details, OSCs without thermal annealing showed a PCE of 7.1%, with a short-circuit current (J(SC)) of 14.9 mA/cm(2), an open-circuit voltage (V-OC) of 0.74 V, and a fill factor (FF) of 64%. The devices annealed at 120 degrees C showed a high PCE of 8.1% with a J(SC) of 15.5 mA/cm(2), a V-OC of 0.74 V, and a FF of 70%. Further increasing the annealing temperature to 150 degrees C led to decreased FF and thereby a relatively lower PCE (7.4%). To the best of our knowledge, the PCE of similar to 8.1% is one of the highest PCE values reported in the literature so far for all polymer solar cells. The high and balanced hole and electron mobility partially contributed to such a high performance. These results suggest that THF as good non-halogenated solvent can be used to fabricate high-performance all polymer solar cells. Higher efficiency can be achieved for OSCs with THF solvent when better polymer acceptors are employed.

Binary all-polymer solar cells with efficiency over 17% by fine-tuning halogenated thiophene linkers of polymer acceptors

Manipulating Polymer Backbone Configuration via Halogenated Asymmetric End-Groups Enables Over 18% Efficiency All-Polymer Solar Cells

Binary All‐polymer Solar Cells with a Perhalogenated‐Thiophene‐Based Solid Additive Surpass 18% Efficiency

Oligomeric Acceptor Enables High‐Performance and Robust All‐Polymer Solar Cells with 17.4% Efficiency

Chlorinated Polymerized Small Molecule Acceptor Enabling Ternary All-Polymer Solar Cells with over 16.6% Efficiency

Synchronously regulating the alkyl side-chain and regioisomer of polymerized small molecule acceptor enabling highly efficient all-polymer solar cells processed with non-halogenated solvent

17.1 %-Efficient Eco-Compatible Organic Solar Cells From A Dissymmetric 3d Network Acceptor

Chlorination of Low-Band-Gap Polymers: Toward High-Performance Polymer Solar Cells

Synergistic Effects of Copolymerization and Fluorination on Acceptor Polymers for Efficient and Stable All-Polymer Solar Cells

Introducing Electron-Withdrawing Linking Units and Thiophene π-Bridges into Polymerized Small Molecule Acceptors for High-Efficiency All-Polymer Solar Cells

An Improved Performance of All Polymer Solar Cells enabled by Sequential Processing via Non-halogenated Solvents

Efficient all-polymer solar cells based on a narrow-bandgap polymer acceptor

High‐Efficiency P3HT‐Based All‐Polymer Solar Cells with a Thermodynamically Miscible Polymer Acceptor

Improved Molecular Ordering in a Ternary Blend Enables All‐Polymer Solar Cells over 18% Efficiency

Improvement in Power Conversion Efficiency of All-Polymer Solar Cells Enabled by Ultrafast Channels for Charge Dynamics

Fluorinated End Group Enables High‐Performance All‐Polymer Solar Cells with Near‐Infrared Absorption and Enhanced Device Efficiency over 14%

Halogen-free Polymer Donors Based on 3,4-Dicyanothiophene for High-performance Polymer Solar Cells

Highly Efficient All‐Polymer Solar Cells Processed from Nonhalogenated Solvents

Nonhalogenated‐Solvent‐Processed High‐Performance All‐Polymer Solar Cell with Efficiency over 14%

A chlorinated polymer promoted analogue co-donors for efficient ternary all-polymer solar cells

High-performance All Polymer Solar Cells Fabricated with Non-halogenated Solvent